JVC SR-VS20U 76 pg User's Manual on the SR-VS20U (1776KB, PDF) - Page 66

Zspecial Features Cont.

Get JVC SR-VS20U - Dual Format S-vhs/minidv Recorder PDF manuals and user guides View all JVC SR-VS20U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

66 EN VCR/TV/CABLE/DBS NUMBER POWER T 1 4 W 2 5 3 2 6 7 8 9 0 4 ENTER 1 DV S-VHS STOP TV CH - 3 TV CH + DBS BRAND NAME JVC (DISH Network) ECHOSTAR (DISH Network) PRIMESTAR SONY (DSS) RCA (DSS) BRAND CODE 51 51 50 41 40 (Ex.) To set remote control to JVC 51: POWER 5 1 STOP Release Hold down Press in succession SPECIAL FEATURES (cont.) DBS Receiver Multi-Brand Remote Control The VCR's remote control can control functions on the brands of DBS (Direct Broadcast Satellite) receivers listed below. TURN ON THE DBS RECEIVER 1 Turn the power on using the DBS receiver's remote control. SET REMOTE CONTROL MODE 2 Set the VCR/TV/CABLE/DBS switch on the VCR's remote control to CABLE/DBS. ENTER DBS RECEIVER BRAND 3 While holding down POWER on the VCR's remote control, use the NUMBER keys to enter the DBS receiver brand number from the chart below and then press STOP. Follow the example shown at bottom left. ● Once you have set the remote control to operate the DBS receiver, you don't have to repeat this step until you replace the remote control's batteries. OPERATE DBS RECEIVER 4 First, press POWER to see if the DBS receiver's power goes off as it should. If it does, try other functions (TV CH +/- and the NUMBER keys can be used to operate the DBS receiver). ● For some brands of DBS receiver, you must press ENTER after having pressed the NUMBER keys. ● To return the remote to VCR control, set the VCR/TV/ CABLE/DBS switch to VCR. NOTES: ● You must set the DBS receiver brand for your remote control and the DBS receiver brand for your Controller (੬ pg. 19) separately. ● Depending on the type of DBS receiver, there may be cases where some or all functions cannot be operated using the remote control. ● It's not possible to operate a DBS receiver that is not equipped with a remote control sensor. ● Though ECHOSTAR has a number of different remote codes, this remote control is applicable only to one of those codes preset at the factory. ● It's not possible to set the remote control for both your DBS receiver and a cable box at the same time. You can only set the remote control to operate one of these units at a time.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
66
EN
DBS Receiver Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands
of DBS (Direct Broadcast Satellite) receivers listed below.
TURN ON THE DBS
RECEIVER
1
Turn the power on using the DBS receiver’s remote
control.
SET REMOTE CONTROL
MODE
2
Set the
VCR/TV/CABLE/DBS
switch on the VCR’s
remote control to CABLE/DBS.
ENTER DBS RECEIVER BRAND
3
While holding down
POWER
on the VCR's remote
control, use the
NUMBER
keys to enter the DBS receiver
brand number from the chart below and then press
STOP
.
Follow the example shown at bottom left.
●
Once you have set the remote control to operate the
DBS receiver, you don't have to repeat this step until
you replace the remote control's batteries.
OPERATE DBS RECEIVER
4
First, press
POWER
to see if the DBS receiver’s power
goes off as it should. If it does, try other functions (
TV
CH +/–
and the
NUMBER
keys can be used to operate
the DBS receiver).
●
For some brands of DBS receiver, you must press
ENTER
after having pressed the
NUMBER
keys.
●
To return the remote to VCR control, set the
VCR/TV/
CABLE/DBS
switch to VCR.
DBS BRAND NAME
BRAND CODE
JVC (DISH Network)
51
ECHOSTAR (DISH Network)
51
PRIMESTAR
50
SONY (DSS)
41
RCA (DSS)
40
NOTES:
●
You must set the DBS receiver brand for your remote control
and the DBS receiver brand for your Controller (
Z
pg. 19)
separately.
●
Depending on the type of DBS receiver, there may be cases
where some or all functions cannot be operated using the
remote control.
●
It's not possible to operate a DBS receiver that is not
equipped with a remote control sensor.
●
Though ECHOSTAR has a number of different remote codes,
this remote control is applicable only to one of those codes
preset at the factory.
●
It's not possible to set the remote control for both your DBS
receiver and a cable box at the same time. You can only set
the remote control to operate one of these units at a time.
(Ex.)
To set remote control to JVC 51:
Release
Hold down
Press in succession
SPECIAL FEATURES (cont.)
1
2
3
4
5
6
7
8
9
0
2
4
1
3
T
W
DV
S-VHS
POWER
STOP
ENTER
NUMBER
VCR/TV/CABLE/DBS
STOP
5
1
POWER
TV CH +
TV CH –