Kenmore 7754 Installation Instructions - Page 4

Gas

Page 4 highlights

C= Level & Position Appliance- Lever appliance by adjusting the (4) levering legs with a wrench. NOTE: A minimum ctearance of 1/8" is required between the bottom of the appliance and the levering leg to allow room for the bracket. Use a spirit lever to check your adjustments. Stide apptiance back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer. For modets with a warmer drawer or Bake-n- Warm TMDouble Oven compartment, grasp the top rear edge of the range and carefully attempt to titt it forward. / :;e,J oeii of _ange --_ 1 1-1/2" _-- I ! o2"i I _Recommended Area for_ i |120V Outlet on Rear of I i |Wall and Area for Thru| _the Wall Connection of|l iPipe Stub and Shut Off| !_ Valve is Shaded Area. j i - .4t Pipe Stub and Shut Off Valve. Fig. 4a Wall Edge Manual Shutoff Valve Flare Union / Flexible Flare Union Pressure Appliance Adaptor Regulator Conduit ! 2. Provide an adequate gas supply. This appliance is factory pre-set to operate on 4" natural gas manifold pressure. A gas pressure regulator is connected to the manifold and MUST be connected in series with the gas supply line. Care must be taken during installation of the appliance not to obstruct the flow of combustion and ventilation air. For proper operation, the maximum inlet pressure to the regulator should be no more than 14 inches of water column pressure. The inlet pressure to the regulator must be at least 1 inch greater than regulator manifold pressure. Examples: If regulator is set for natural gas 4 inch manifold pressure, inlet pressure must be at least 5 inches. Leak testing of the appliance shall be conducted according to the instructions in step 4g. The gas supply line should be 1/2" or 3/4" I.D. 3. Seal wall openings. Seal any openings in the wall behind the appliance and in the floor under the appliance after gas supply line is installed. 4. Connect the appliance to the gas supply. NOTE: To prevent leaks use pipe joint sealant on all male (outside) pipe threads. Off Service Shut-Off Valve Electric Ignition m_'-o''d4e'_lslco,,_n,lny__ (Shown in ON Position). Be sure lever is in the "On" position when installation is complete Fig. 4b Gas io o Gas Regulator Regulator I_ 2 Gas Shut-Off Valve (shown in the "ON" position,) Fig. 4c

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

C=
Level
&
Position
Appliance-
Lever appliance by adjusting
the (4) levering legs with a wrench.
NOTE: A minimum
ctearance of 1/8" is required between
the bottom of the
appliance
and the levering
leg to
allow
room
for
the
bracket.
Use a spirit lever to check your
adjustments.
Stide apptiance
back into position.
Visually
check that
rear leveling leg is inserted into and fully secured by the
Anti-Tip
Bracket
by removing
lower
panel
or storage
drawer.
For modets with a warmer
drawer
or Bake-n-
Warm TMDouble Oven compartment,
grasp the top rear
edge
of the range and carefully
attempt to titt it forward.
2.
Provide
an adequate
gas
supply.
This appliance is factory pre-set to operate on 4" natural gas
manifold
pressure. A gas pressure regulator is connected to
the manifold and MUST be connected
in series with the gas
supply line.
Care must be taken during installation of the appliance not to
obstruct the flow of combustion
and ventilation
air.
For proper
operation,
the maximum
inlet
pressure
to the
regulator should be no more than 14 inches of water column
pressure. The inlet pressure to the regulator must be at least
1 inch greater than regulator manifold pressure. Examples:
If
regulator is set for natural gas 4 inch manifold pressure, inlet
pressure
must be at least 5 inches.
Leak testing of the appliance shall be conducted according to
the instructions
in step 4g.
The gas supply line should be 1/2" or 3/4" I.D.
3.
Seal wall
openings.
Seal any openings
in
the wall behind the appliance and in the
floor under the appliance
after gas supply line is installed.
4.
Connect
the appliance
to the
gas
supply.
NOTE:
To prevent
leaks use pipe joint
sealant on all male
(outside) pipe threads.
/
J
ii
:;e,oe
of _ange
--_
1 1-1/2" _--
I
_Recommended
Area
for_ i
|120V
Outlet
on Rear of I
i |Wall
and
Area
for Thru|
_the
Wall
Connection
of|l
iPipe
Stub
and
Shut
Off|
!_
Valve
is Shaded
Area.
j
I
!
o2"i
i
Pipe Stub
and
Shut
Off
Valve.
Fig. 4a
-
.4t
Wall
Edge
Manual
Flare
Flexible
Flare Union
Pressure
Shutoff
Union
Appliance
Adaptor
Regulator
Valve
/
Conduit
!
Off
Service Shut-Off Valve Electric Ignition models onl
_'-''4'_lc
,,_,ny__
(Shown in ON Position).
Be sure lever is in the "On" position when
installation is complete
Fig. 4b
Gas
Regulator
o
o
Gas i
Regulator
I_
Gas Shut-Off
Valve
(shown
in the
"ON"
position,)
Fig. 4c
2