Kenwood KDC-X889 Instruction Manual - Page 11

Adjust the Basic Audio item

Get Kenwood KDC-X889 PDF manuals and user guides View all Kenwood KDC-X889 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [VOL] knob. 3 Select the Basic Audio item for adjustment Press the [VOL] knob. Each time the knob is pressed, the items that can be adjusted switch as shown below. 4 Adjust the Basic Audio item Turn the [VOL] knob. Adjustment Item Display Range Rear Volume *1 "Rear Volume" 0 - 35 Subwoofer level*2,3,4 "Sub-WLevel" -15 - +15 Bass level*5 "Bass Level" -8 - +8 Middle level*5 "Middle Level" -8 - +8 Treble level*5 "Treble Level" -8 - +8 Balance "Balance" Left 15 - Right 15 Fader*4 "Fader" Rear 15 - Front 15 Exit Audio Control mode • *1 You can control this item when "2 ZONE" of (page 12) is set to "ON". • *2 You can control this item when (page 43) is set to "SWPRE Sub-W". (KDC-MP728/ KDC-MP628 only) • *3 You can control this item when (page 14) is set to "SW ON". • *4 You can control this item when "2 ZONE" of (page 12) is set to "OFF". • *5 These items can be adjusted in detail by the following methods. (Function of the KDC-X789) • *5 Source tone memory: The set up value is put in the memory per source. (Detail Audio item is included) 5 Exit Audio Control mode Press any button. Press the button which is not [VOL] knob and [ATT]/[ANG] button. Adjust the detail of Audio Control (Function of the KDC-X789) 1 Select the Audio item for adjustment By referring to the step 1 - 3 above, select the desired item to be set in detail from the items marked with *5. 2 Enter Detail adjustment mode of Audio Control Press the [VOL] knob for at least 1 second. 3 Select the Detail Audio item for adjustment Press the [VOL] knob. Each time the knob is pressed, the items that can be adjusted switch as shown below. 4 Adjust the Detail Audio item Turn the [VOL] knob. Bass level Adjustment Item Display Range Bass Center Frequency "Bass FRQ" 40/50/60/70/80/100/ 120/150 Hz Bass Q Factor Bass Extend "Bass Q Factor" 1.00/1.25/1.50/2.00 "Bass EXT" OFF/ON Middle level Adjustment Item Display Range Middle Center Frequency "Middle FRQ" 0.5/1.0/1.5/2.0 kHz Middle Q Factor "Middle Q Factor" 1.00/2.00 Treble level Adjustment Item Display Range Treble Center Frequency "Treble FRQ" 10.0/12.5/15.0/17.5 kHz 5 Exit the Detail Audio Control mode Press the [VOL] knob for at least 1 second. • When the Bass Extend is set to ON, low frequency response is extended by 20%. • You can exit the Audio Control mode at anytime by pressing any button except for [VOL] and [ATT]/[ANG] buttons. English | 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
English
|
11
1
Select the source for adjustment
Press the [SRC] button.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Select the Basic Audio item for adjustment
Press the [VOL] knob.
Each time the knob is pressed, the items that can
be adjusted switch as shown below.
4
Adjust the Basic Audio item
Turn the [VOL] knob.
Adjustment Item
Display
Range
Rear Volume *
1
"Rear Volume"
0 — 35
Subwoofer level*
2,3,4
"Sub-WLevel"
–15 — +15
Bass level*
5
"Bass Level"
–8 — +8
Middle level*
5
"Middle Level"
–8 — +8
Treble level*
5
"Treble Level"
–8 — +8
Balance
"Balance"
Left 15 — Right 15
Fader*
4
"Fader"
Rear 15 — Front 15
Exit Audio Control mode
• *
1
You can control this item when "2 ZONE" of <Audio
Setup> (page 12) is set to "ON".
• *
2
You can control this item when <Switching preout>
(page 43) is set to "SWPRE Sub-W". (KDC-MP728/
KDC-MP628 only)
• *
3
You can control this item when <Subwoofer
Output> (page 14) is set to "SW ON".
• *
4
You can control this item when "2 ZONE" of <Audio
Setup> (page 12) is set to "OFF".
• *
5
These items can be adjusted in detail by the
following methods. (Function of the KDC-X789)
• *
5
Source tone memory: The set up value is put in the
memory per source. (Detail Audio item is included)
5
Exit Audio Control mode
Press any button.
Press the button which is not [VOL] knob and
[ATT]/[ANG] button.
Adjust the detail of Audio Control
(Function of the KDC-X789)
1
Select the Audio item for adjustment
By referring to the step 1 — 3 above, select the
desired item to be set in detail from the items
marked with *
5
.
2
Enter Detail adjustment mode of Audio
Control
Press the [VOL] knob for at least 1 second.
3
Select the Detail Audio item for adjustment
Press the [VOL] knob.
Each time the knob is pressed, the items that
can be adjusted switch as shown below.
4 Adjust the Detail Audio item
Turn the [VOL] knob.
Bass level
Adjustment Item
Display
Range
Bass Center Frequency
"Bass FRQ"
40/50/60/70/80/100/
120/150 Hz
Bass Q Factor
"Bass Q Factor" 1.00/1.25/1.50/2.00
Bass Extend
"Bass EXT"
OFF/ON
Middle level
Adjustment Item
Display
Range
Middle Center
Frequency
"Middle FRQ"
0.5/1.0/1.5/2.0 kHz
Middle Q Factor
"Middle Q Factor"
1.00/2.00
Treble level
Adjustment Item
Display
Range
Treble Center Frequency
"Treble FRQ"
10.0/12.5/15.0/17.5 kHz
5 Exit the Detail Audio Control mode
Press the [VOL] knob for at least 1 second.
• When the Bass Extend is set to ON, low frequency
response is extended by 20%.
• You can exit the Audio Control mode at anytime by
pressing any button except for [VOL] and [ATT]/[ANG]
buttons.