Kenwood KDC-X889 Instruction Manual - Page 15
Sound Management system
View all Kenwood KDC-X889 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
5 Adjust the Sound Field Control item Push the Control knob to [4] or [¢]. Each time the knob is pushed, the setting switches as shown below. Sound Field Control Item Range Front High Pass Filter Center/ Rear High Pass Filter Center (KDC-X889) Through/30 - 100/120/150/ 180/220/250 (Hz) (KDC-MP828) Through/40/60/80/100/120/ 150/180/220 (Hz) Front High Pass Filter Slope/ Rear High Pass Filter Slope/ Subwoofer Low Pass Filter Slope* (KDC-X889) -12/-18/-24 dB/oct (KDC-MP828) -12/-18 dB/oct Subwoofer Low Pass Filter Center* (KDC-X889) 30 - 100/120/150/180/220/ 250 (Hz)/Through (KDC-MP828) 40/60/80/100/120/150/180/ 220 (Hz)/Through Subwoofer Low Pass Filter Phase* Reverse/ Normal DTA Front/DTA Rear DTA Subwoofer* 0 - 20.33 (feet) Position Setting Front-L/ Front-R/ Front/ ALL 2 Select the key function section Press the [NEXT] button. Repeatedly press the button until "S.M.S" is displayed above the [2] button. Refer to (page 9). 3 Enter Sound Management mode Press the [2] ("S.M.S") button. • When "2 ZONE" of (page 13) is ON, you cannot select "S.M.S". 4 Select the Sound Management item for adjustment Press the [1] - [5] button. Multi-function key operation [1] "CABIN" [2] "F" [3] "R" [4] "SW" [5] "Preset" [1] "CALL" [2] "MEM" Sound Management Item Cabin Setting Speaker Select Front Speaker Select Rear Speaker Select Subwoofer Call mode Memory mode • To get the best sound, first set the Cabin Setting and Speaker Select Front/Rear parameters using the (page 15). • When the "2 ZONE" of (page 13) is "ON", each of the following setup is ignored. - "Xover" - "DTA" - "POSI" - "Preset" • * You can control this item when (page 14) is set to "SW ON". • * You can control this item when Speaker Select Subwoofer of (page 15) is set to any item other than "None". 6 Exit Sound Field Control mode Press the [6] ("RTN") button. Function of the KDC-X889/KDC-MP828 Sound Management system 1 Select the source for adjustment Press the [SRC] button. • "Preset": You can store an adjusted sound management system value by selecting "MEM". Refer to (page 18). Also, you can recall it by selecting "CALL". Refer to (page 18). 5 Adjust the Sound Management item Push the Control knob to [4] or [¢]. Each time the knob is pushed, the setting switches as shown below. Sound Managemnt Item Cabin Setting Speaker Select Front Speaker Select Rear Speaker Select Subwoofer Range OFF/ COMPACT/ FULL SIZE CAR/ WAGON1/ WAGON2/ MINI VAN1/ MINI VAN2/ SUV/ MINI VAN LONG 6 ½/ 6 ¾/ 7/ 4x6/ 5x7/ 6x8/ 6x9/ 7x10/ OEM/ 4/ 5 (inch) 6 ½/ 6 ¾/ 7/ 4x6/ 5x7/ 6x8/ 6x9/ 7x10/ None/ OEM/ 4/ 5 (inch) 8/ 10/ 12/ 15over/ None/ 6 ½(inch) 6 Exit Sound Managemnt mode Press the [6] ("RTN") button. English | 15