Kyocera TASKalfa 500ci Kyocera Command Center Operation Guide Rev 6.3 - Page 12

Basic Basic > Defaults > Network - driver

Get Kyocera TASKalfa 500ci PDF manuals and user guides View all Kyocera TASKalfa 500ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

COMMAND CENTER Pages Download Drivers For downloading printer drivers, etc.: http://www.kyoceramita.com/download/ Kyocera Online For more information about products: http://www.kyoceramita.com/ Basic Page This section includes settings that apply to the machine, such as Device Defaults, Security, and basic Networking. Basic > Defaults > Network This page allows you to make the settings that are required for network printing and sending E-mail. For more information, refer to Advanced > Protocols > TCP/IP > General on page 3-35. You must restart this machine after you have completed these settings in order to properly register the content of those settings in the machine. Refer to Basic > Defaults > Reset on page 3-6. Host Name Specifies a name for the printing system network component. This name is used as the NetBEUI printer name and as the WSD device name. LAN Interface Specifies the communication rate from Auto, 10BASE-T-Half, 10BASE-T-Full, 100BASE-TX-Half, 100BASE-TX-Full and 1000BASE-T. If you change the communication rate, you must restart the machine in order to make this setting valid. Refer to . IPv4 Settings • DHCP/BOOTP Specifies whether or not to obtain an IP address using DHCP or BOOTP. • IP Address (IPv4) Assigns the Internet Protocol address on the printing system network component. Format of the IP address is four-byte (32-bit) numbers separated by dots, e.g. 192.168.110.171. • Subnet Mask Specifies the subnet mask of the hosts or network with which the print system is connecting. If you have manually assigned an IP address that starts with a number between 192 and 223, it is recommended that you set the subnet mask to "255.255.255.0." • Default Gateway Specifies the IP address of the default gateway. IPv6 Settings • IPv6 Specifies whether or not to enable the IPv6 protocol. Select On to use the IPv6 protocol. • IP Address (IPv6) 3-5 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
COMMAND CENTER Pages
Download Drivers
For downloading printer drivers, etc.:
Kyocera Online
For more information about products:
Basic Page
This section includes settings that apply to the machine, such as Device
Defaults, Security, and basic Networking.
Basic > Defaults > Network
This page allows you to make the settings that are required for network printing
and sending E-mail. For more information, refer to
Advanced > Protocols >
TCP/IP > General
on page 3-35.
You must restart this machine after you have completed these settings in order
to properly register the content of those settings in the machine. Refer to
Basic
> Defaults > Reset
on page 3-6.
Host Name
Specifies a name for the printing system network component. This name is
used as the NetBEUI printer name and as the WSD device name.
LAN Interface
Specifies the communication rate from
Auto
,
10BASE-T-Half
,
10BASE-T-Full
,
100BASE-TX-Half
,1
00BASE-TX-Full
and
1000BASE-T
. If
you change the communication rate, you must restart the machine in order to
make this setting valid. Refer to .
IPv4 Settings
•
DHCP/BOOTP
Specifies whether or not to obtain an IP address using DHCP or BOOTP.
•
IP Address (IPv4)
Assigns the Internet Protocol address on the printing system network
component. Format of the IP address is four-byte (32-bit) numbers separated
by dots, e.g. 192.168.110.171.
•
Subnet Mask
Specifies the subnet mask of the hosts or network with which the print system
is connecting. If you have manually assigned an IP address that starts with a
number between 192 and 223, it is recommended that you set the subnet
mask to "255.255.255.0."
•
Default Gateway
Specifies the IP address of the default gateway.
IPv6 Settings
•
IPv6
Specifies whether or not to enable the IPv6 protocol. Select
On
to use the
IPv6 protocol.
•
IP Address (IPv6)
User Guide
3-5