LG 32LD655H Owners Manual - Page 110

COMMERCIAL MODE SETUP COMMERCIAL MODE SETUP 110 040 - AUTO CAMPORT Set to 1 to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection. NOTE: If set to 1, 093 RJP Available is automatically set to 0. 073 - CH NOT AVBLE (Channel Not Available) If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, "NOT AVAILABLE" message is displayed when directly accessing a channel not in the channel scan list available in memory. 046 - STRT AUX SRCE (Start Aux Source) Sets the starting AUX source. At power up, TV will tune to starting Aux source if item 004 Start Channel is set to 0. If item 093 RJP Available is set to 0 and item 040 Auto Camport is set to 0: 1 = Video 1 4 = RGB 255 = Last Aux 2 = Video 2 5 = HDMI 2 3 = HDMI 1 6 = Component If item 093 RJP Available is set at 1: 2 = Video 2 5 = HDMI 2 6 = Component 075 - REVERT CH (Revert to Start Channel) If set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel. 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by M.P.I. command. Note: Not linked to serial number. 079 - UPN MSB-1 (UPN Most Significant Byte-1) User programmable number, most significant byte-1 readable by M.P.I. command. Not linked to serial number. If item 040 Auto Camport is set to 1: 1 = Video 1 5 = HDMI 2 3 = HDMI 1 6 = Component 4 = RGB 047 - AUX STATUS Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change. Controls M.P.I. status channel response for AUX inputs. 053 - DIS. CH-TIME (Disable Channel-Time) Set to 1 to disable the Channel-Time display, Channel-Time display will not appear. Set to 0 to enable the Channel-Time display. 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu background is transparent. 071 - BCK. CH-TIME (Channel-Time Display Background Color) Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu background is transparent. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by M.P.I. command. Not linked to serial number. 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by M.P.I. command. Not linked to serial number. 082 - CHKSM ERROR (Checksum Error) Enforces rigid M.P.I. checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on M.P.I. async port). SPI is always checked. 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 5. (Timeout = 25.5MS + [25.5 MS* Handshake time]). 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes. 087 - REAR RGB EN. (Rear RGB Enable) Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 2 for PC for STB RGB input. (For 32/37/42LG710H) Set to 1 for PC for STB RGB input. (For 32/37/42/47/55LD650H, 32/37/42LD655H) Set to 18 for Auto Configure one time only with power cord removal and reinsertion. (For 32/37/42LG710H) Set to 17 for Auto Configure one time only with power cord removal and reinsertion.(For 32/37/42/47/55LD650H, 32/37/42LD655H) 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present.