LG 32LG3DCH Setup Guide - Page 23

Installer Menu (Cont.) 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by MPI command. Not linked to serial number. 079 - UPN MSB-1 (UPN Most Significant Byte-1) User programmable number, most significant byte-1 readable by MPI command. Not linked to serial number. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by MPI command. Not linked to serial number. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up. • Set to 0 for Set By System. • Set to 1 for 4:3. • Set to 2 for 16:9 (Factory Default). • Set to 3 for Just Scan. (LG3DDH only) • Set to 4 for Zoom. (Zoom 1 for LG3DCH) • Set to 5 for Zoom 2. (LG3DCH only) Note: Only applies if item 106 ASP RATIO LOCK is disabled, set to 0. 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by MPI command. Not linked to serial number. 082 - CHKSM ERROR (Checksum Error) Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked. 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PCbased Windows controlled systems. Range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time].) 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes. 087 - REAR RGB EN. (Rear RGB Enable) Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 2 (LG3DCH) / 1 (LG3DDH) to enable for RGB PC input. Set to 18 (LG3DCH) / 17 (LG3DDH) to initiate a one-time automatic configuration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed. 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present. 090 - KEY LOCK If set to 1, front keyboard Channel, Volume, and Captions buttons are disabled, Power button remains enabled. If set to 0, the Channel, Volume, Captions, and Power buttons are all enabled. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function menu, if Function Menu is available. Set to 0 to disable SAP feature on Function Menu, if Function Menu is available. 099 - BACK LIGHTING Sets the TV screen brightness at power up. LG3DCH: Default setting is 100. LG3DDH: Default setting is 200. • 1 - 100 Static Back Lighting (1 = Dimmest picture, 100 = Brightest picture) • 101 - 200 Dynamic Back Lighting (101 = Dimmest picture, 200 = Brightest picture) If settings are above 200, the TV automatically controls back lighting depending upon the picture level of the current program. 102 - ATSC BAND Sets up TV to receive different types of incoming signals: 0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC. 103 - ATSC TUNE MODE Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan. 104 - START MINOR CHANNEL Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel's Minor Start Channel number. 106 - ASP RATIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP. RATIO above. 116 - VIDEO MUTE EN (Video Mute Enable) Set to 0 for Normal. Set to 1 for Blank. 117 - FACT DEFAULT (Factory Default) Set to 0 for normal. Set to 1 to load presets of all Installer Menu item settings. Setting this item to 1 will also reinitiate the Express Script Installer Menu Wizard (see pages 16 - 17). Warning: If set to 1, this will reload the factory defaults and clear the Channel List, including any assigned channel icons and custom channel labels. 206-4096 23