LG 32LG3DCH Setup Guide - Page 26

Channel Banks Overview

Page 26 highlights

Channel Banks Overview Channel Banks Note: Disable all Aux sources in the Installer Menu that will not be made available to the end user. Channel banks enable institution administrators to control access to patient in-room TV programming. A channel bank can be enabled for a patient for a pre-determined fee. For Channel Banks 1, 2, and 3, the institution can create programming levels. Each level offers a custom channel lineup. The top tier generally contains the most programming (premium, etc.), 2nd tier = lesser programming, 3rd tier = basic programming, etc. If an Inactive TV display (described on the following page) has been created on Channel Bank 4, an "Inactive TV Call Attendant" message appears when the TV is turned On. An administrator can then activate Channel Bank 1, 2, or 3 depending on the programming tier selected by the patient. When the patient leaves the hospital, the administrator can then select Channel Bank 4 to reinstate the "Inactive TV" message. Channels Available Charts All channels found in the channel search are included in each of the channel banks. The default is for all channels to be active in Channel Banks 1, 2, 3, and 4. Create channel banks charts similar to the examples on the following pages. On the channel bank charts, show the status for each channel in all channel banks. This then becomes the patient entertainment programming offerings plan. Setting Up Channel Banks The LG Installer Remote is required to access the Channel Banks Setup Menu (see example above at right) and administer channel banks. Refer to "Channel Banks Setup" on the following pages for detailed information on using the Installer Remote to setup and administer channel banks. Before you begin to set up channel banks, note the following: • Complete either the Commercial Mode Setup procedure or run the Express Script Installer Menu Wizard (see pages 14 to 15 or pages 16 to 17, respectively). Channel banks can only be set up after the TV setup has been transferred to the internal TV controller (PTC). • Installer Menu item 028 CH. OVERIDE must be set to 001 to allow access for channel banks setup. Note: The default setting for Aux sources is to be active in the Installer Menu. The Aux sources will appear between the highest analog and lowest digital channel number in the channel scan with Channel Up/Down. If the Aux sources will not be used, it is advisable to set them to 000 (Off) before running 2-5-5 + MENU (Commercial Mode Setup) or completing the Express Script Installer Menu Wizard. After running 2-5-5 + MENU/completing the Express Script, the only way to turn the Aux sources off so they will not appear in the channel scan, is to go to the Channel Banks Setup Menu and select NORMAL-DELETED. If performing the Commercial Mode Setup procedure, refer to Installer Menu items: 034, 035, 038, 039 and 087. If running the Express Script, customize the Aux inputs as appropriate in the Aux Input screen of the Installer Menu Wizard. CHANNEL PREVIEW - BANK 1 CH 011-001 NORMAL-ADDED Enter -> Change CC -> VCHIP Menu, Ch. Preview -> Exit Channel Banks Setup Menu MUTE POWER CH BANK PREVIEW GUIDE SAP INFO CC CH OK VOL VOL CH FLASHBK TIMER MENU ALARM ADJ ADJ ADJ ADJ BED1 BED2 Use the Installer Remote to access the Channel Banks Setup Menu. 26 206-4096

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47

26
206-4096
Channel Banks Overview
Channel Banks Note: Disable all Aux sources in the Installer Menu that will not be made available to the end user.
Channel banks enable institution administrators to control access to
patient in-room TV programming. A channel bank can be enabled for a
patient for a pre-determined fee. For Channel Banks 1, 2, and 3, the insti-
tution can create programming levels. Each level offers a custom channel
lineup. The top tier generally contains the most programming (premium,
etc.), 2nd tier = lesser programming, 3rd tier = basic programming, etc. If
an Inactive TV display (described on the following page) has been created
on Channel Bank 4, an “Inactive TV Call Attendant” message appears
when the TV is turned On. An administrator can then activate Channel
Bank 1, 2, or 3 depending on the programming tier selected by the patient.
When the patient leaves the hospital, the administrator can then select
Channel Bank 4 to reinstate the “Inactive TV” message.
Channels Available Charts
All channels found in the channel search are included in each of the chan-
nel banks. The default is for all channels to be active in Channel Banks 1,
2, 3, and 4. Create channel banks charts similar to the examples on the
following pages. On the channel bank charts, show the status for each
channel in all channel banks. This then becomes the patient entertainment
programming offerings plan.
Setting Up Channel Banks
The LG Installer Remote is required to access the Channel Banks Setup
Menu (see example above at right) and administer channel banks. Refer
to “Channel Banks Setup” on the following pages for detailed information
on using the Installer Remote to setup and administer channel banks.
Before you begin to set up channel banks, note the following:
Complete either the Commercial Mode Setup procedure or run the Ex-
press Script Installer Menu Wizard (see pages 14 to 15 or pages 16 to
17, respectively). Channel banks can only be set up after the TV setup
has been transferred to the internal TV controller (PTC).
Installer Menu item 028 CH. OVERIDE must be set to 001 to allow
access for channel banks setup.
Channel Banks Setup Menu
CHANNEL PREVIEW - BANK 1
CH 011-001
NORMAL-ADDED
Enter -> Change
CC -> VCHIP Menu,
Ch. Preview -> Exit
MUTE
POWER
BANK
GUIDE
CH
PREVIEW
SAP
INFO
CC
OK
VOL
CH
CH
VOL
FLASHBK
TIMER
ALARM
MENU
ADJ
ADJ
ADJ
ADJ
BED1
BED2
Use the Installer Remote to
access the Channel Banks
Setup Menu.
Note:
The default setting for Aux sources is to be active in the Installer Menu. The
Aux sources will appear between the highest analog and lowest digital channel
number in the channel scan with Channel Up/Down. If the Aux sources will not be
used, it is advisable to set them to 000 (Off) before running 2-5-5 + MENU
(Commercial Mode Setup) or completing the Express Script Installer Menu Wizard.
After running 2-5-5 + MENU/completing the Express Script, the only way to turn the
Aux sources off so they will not appear in the channel scan, is to go to the Channel
Banks Setup Menu and select NORMAL-DELETED. If performing the Commercial
Mode Setup procedure, refer to Installer Menu items: 034, 035, 038, 039 and 087.
If running the Express Script, customize the Aux inputs as appropriate in the Aux
Input screen of the Installer Menu Wizard.