LG LSEL6331F Owners Manual - Page 19

-Wire Connection: Conduit, ENGLISH

Get LG LSEL6331F PDF manuals and user guides View all LG LSEL6331F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

ENGLISH 2 Insert the bare wire (white/neutral) end through the center terminal block opening. Do not remove the ground strap connections. 3 Insert the two side bare wire ends into the lower left and the lower right terminal block openings. 4 Tighten the 3 screws securely into the terminal block. (approximately 35 - 50 IN-LB) INSTALLATION 19 Conduit Installations CAUTION • Do not install the conduit without a strain relief. 1 Remove the cord/conduit connection plate from the rear of the oven and rotate it. • The conduit hole (1 1/8") must be used. 2 Prepare the conduit wires as shown below. a Black b White c Red d Terminal block e Wire ends f Conduit connection plate 4-Wire Connection: Conduit WARNING • The white middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of the main terminal block. The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. The 4th ground wire (green) must be connected to the frame of the range with the ground screw. Failure to do so can result in electrical shock, severe personal injury or death. • If screws are not tightened securely, it can result in electrical spark and severe personal injury or death. a Cord/Conduit connection plate b Ground wire 3 Install the conduit strain relief. 1) Insert the strain relief in the 1 1/8 in. (2.8 cm) conduit hole. 2) Install the conduit through the body of the strain relief and fasten the strain relief with its ring. NOTE • For conduit installations, purchase a strain relief. 4 Reinstall the cord/conduit connection plate. Conduit Connections If the wire in the conduit is copper it must be 8 or 10 AWG wiring. If the wire in the conduit is aluminum it must be 6 or 8 AWG wiring. 1 Loosen the 2 lower left and right screws from the terminal block. Remove the lower 2 center screws. Do not discard any screws. 2 Remove the ground screw and bend the end of the ground strap up so the slot is over the hole of the center screw removed in step 1.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
19
INSTALLATION
ENGLISH
2
Insert the bare wire (white/neutral) end
through the center terminal block opening.
Do not remove the ground strap connections.
3
Insert the two side bare wire ends into the
lower left and the lower right terminal block
openings.
4
Tighten the 3 screws securely into the
terminal block. (approximately 35 - 50 IN-LB)
a
Black
b
White
c
Red
d
Terminal block
e
Wire ends
f
Conduit connection plate
4-Wire Connection: Conduit
WARNING
•
The white middle (neutral) wire of the power
cord or 4-wire conduit has to be connected to
the middle post of the main terminal block. The
other two wires of the power cord or conduit
have to be connected to the outside posts of the
main terminal connection block. The 4th ground
wire (green) must be connected to the frame of
the range with the ground screw. Failure to do
so can result in electrical shock, severe personal
injury or death.
•
If screws are not tightened securely, it can result
in electrical spark and severe personal injury or
death.
Conduit Installations
CAUTION
•
Do not install the conduit without a strain relief.
1
Remove the cord/conduit connection plate
from the rear of the oven and rotate it.
•
The conduit hole (1 1/8") must be used.
2
Prepare the conduit wires as shown below.
a
Cord/Conduit connection plate
b
Ground wire
3
Install the conduit strain relief.
1)
Insert the strain relief in the 1 1/8 in. (2.8
cm) conduit hole.
2)
Install the conduit through the body of
the strain relief and fasten the strain relief
with its ring.
NOTE
•
For conduit installations, purchase a strain relief.
4
Reinstall the cord/conduit connection plate.
Conduit Connections
If the wire in the conduit is copper it must be 8 or
10 AWG wiring.
If the wire in the conduit is aluminum it must be 6
or 8 AWG wiring.
1
Loosen the 2 lower left and right screws from
the terminal block. Remove the lower 2 center
screws. Do not discard any screws.
2
Remove the ground screw and bend the end
of the ground strap up so the slot is over the
hole of the center screw removed in step 1.