Lenovo ThinkPad X30 English - Service and Troubleshooting Guide for ThinkPad X - Page 23

Troubleshooting, Error messages, Solving computer problems

Get Lenovo ThinkPad X30 PDF manuals and user guides View all Lenovo ThinkPad X30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Solving computer problems Troubleshooting If you do not find your problem here, refer to Access ThinkPad, your on-board help system. Open Access ThinkPad by pressing the ThinkPad button. The following section only describes problems that might prevent you from accessing this help system. Error messages Notes: 1. In the charts, x can be any character. 2. The version of PC-Doctor referred to here is PC-Doctor for Windows. Message Solution 0175: Bad CRC1, stop POST task The EEPROM checksum is not correct (block #6). Have the computer serviced. 0176: System Security The System has been tampered with. This message is displayed if you remove the Security Chip and reinstall it, or install a new one. To clear the error, enter the BIOS Setup Utility. If this does not solve the problem, have the computer serviced. 0187: EAIA data access The access to EEPROM is failed. Have the computer serviced. error 0188: Invalid RFID The EEPROM checksum is not correct (block # 0 and 1, or block # 6). The serialization information system board should be replaced, and the box serial number needs to be area or bad CRC2. reinstalled. Have the computer serviced. 0189: Invalid RFID configuration information area The EEPROM checksum is not correct (block # 4 and 5). The system board should be replaced, and the UUID needs to be reinstalled. Have the computer serviced. 0190: Critical low-battery The computer turned off because the battery is low. Connect the ac adapter error to the computer and charge the battery, or replace the battery with a fully charged one. 0191: System Security Invalid remote change requested. The system configuration change has failed. Confirm the operation and try again.To clear the error, enter the BIOS Setup Utility. 0192: System Security IBM Embedded Security hardware tamper detected. The Security Chip has been replaced with a different one. Have the computer serviced. 0197: Invalid Remote change requested The remote configuration for the Security Chip has failed. Confirm the operation and try again. 0199: System Security IBM Security password retry count exceeded. This message is displayed if you enter a wrong supervisor password more than three times. Confirm the supervisor password and try again. To clear the error, enter the BIOS Setup Utility. Chapter 2. Solving computer problems 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Troubleshooting
If you do not find your problem here, refer to Access ThinkPad, your
on-board help system. Open Access ThinkPad by pressing the ThinkPad
button. The following section only describes problems that might prevent you
from accessing this help system.
Error messages
Notes:
1.
In the charts, x can be any character.
2.
The version of PC-Doctor referred to here is PC-Doctor for Windows.
Message
Solution
0175: Bad CRC1, stop
POST task
The EEPROM checksum is not correct (block #6). Have the computer
serviced.
0176: System Security -
The System has been
tampered with.
This message is displayed if you remove the Security Chip and reinstall it,
or install a new one. To clear the error, enter the BIOS Setup Utility. If this
does not solve the problem, have the computer serviced.
0187: EAIA data access
error
The access to EEPROM is failed. Have the computer serviced.
0188: Invalid RFID
serialization information
area or bad CRC2.
The EEPROM checksum is not correct (block # 0 and 1, or block # 6). The
system board should be replaced, and the box serial number needs to be
reinstalled. Have the computer serviced.
0189: Invalid RFID
configuration
information area
The EEPROM checksum is not correct (block # 4 and 5). The system board
should be replaced, and the UUID needs to be reinstalled. Have the
computer serviced.
0190: Critical low-battery
error
The computer turned off because the battery is low. Connect the ac adapter
to the computer and charge the battery, or replace the battery with a fully
charged one.
0191: System Security -
Invalid remote change
requested.
The system configuration change has failed. Confirm the operation and try
again.To clear the error, enter the BIOS Setup Utility.
0192: System Security -
IBM Embedded Security
hardware tamper
detected.
The Security Chip has been replaced with a different one. Have the
computer serviced.
0197: Invalid Remote
change requested
The remote configuration for the Security Chip has failed. Confirm the
operation and try again.
0199: System Security -
IBM Security password
retry count exceeded.
This message is displayed if you enter a wrong supervisor password more
than three times. Confirm the supervisor password and try again. To clear
the error, enter the BIOS Setup Utility.
Solving computer problems
Chapter 2. Solving computer problems
11