Lexmark X642E Menus and Messages - Page 26

Universal Setup, Reports

Get Lexmark X642E - X642E PDF manuals and user guides
UPC - 734646258746
View all Lexmark X642E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Using MFP menus Universal Setup These menu items are used to specify the height and width of the Universal Paper Size. When the height and width for Universal Paper Size are specified, the MFP uses the Universal setting like other paper sizes, including support for duplex and n-up. For more information on n-up, see Multipage Print. Menu item Purpose Values and descriptions Units of Measure Determines the unit of measure used to enter the Universal Height and Width. Inches Millimeters Inches is the US default, and Millimeters is the international default. Portrait Width Sets the portrait width of the universal media. Note: If the value set exceeds the maximum width, the MFP uses the maximum value allowed in inches or millimeters. 3-14.17 inches in 0.01 inch increments 76-360 mm in 1 mm increments Shows either inches or millimeters from the Units of Measure setting; 8.5 inches is the US default, and 216 mm is the international default. Portrait Height Sets the portrait height of the universal media. Note: If the value set exceeds the maximum height, the MFP uses the maximum value allowed in inches or millimeters. 3-14.17 inches in 0.01 inch increments 76-360 mm in 1 mm increments Shows either inches or millimeters from the Units of Measure setting; 14 inches is the US default, and 356 mm is the international default. Feed Direction Specifies the feed direction of the Universal Paper Size. Short Edge* Long Edge Feed Direction is only shown if the Long Edge value is available. Long Edge exists if the longest edge is shorter than the maximum physical width that the tray can accommodate. See Duplex Bind on page 70 for more information about short and long edges. Reports Note: After a report prints, the MFP returns to the home screen. Each report prints using some standard print settings, such as: • one copy • portrait orientation • 600 dots per inch (dpi) print resolution • normal print area • no separator sheets • duplex printing is set off • multiple page printing is set off • toner darkness is set to eight • media source is the user default Reports 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Reports
26
Using MFP menus
Universal Setup
These menu items are used to specify the height and width of the Universal Paper Size. When the height and width for
Universal Paper Size are specified, the MFP uses the Universal setting like other paper sizes, including support for duplex
and n-up. For more information on n-up, see
Multipage Print
.
Reports
Note:
After a report prints, the MFP returns to the home screen.
Each report prints using some standard print settings, such as:
•
one copy
•
portrait orientation
•
600 dots per inch (dpi) print resolution
•
normal print area
•
no separator sheets
•
duplex printing is set off
•
multiple page printing is set off
•
toner darkness is set to eight
•
media source is the user default
Menu item
Purpose
Values and descriptions
Units of Measure
Determines the unit of measure
used to enter the Universal Height
and Width.
Inches
Millimeters
Inches is the US default, and
Millimeters is the international default.
Portrait Width
Sets the portrait width of the
universal media.
Note:
If the value set exceeds the
maximum width, the MFP uses the
maximum value allowed in inches or
millimeters.
3–14.17 inches in
0.01 inch increments
76–360 mm in 1 mm
increments
Shows either inches or millimeters
from the Units of Measure setting;
8.5 inches is the US default, and
216 mm is the international default.
Portrait Height
Sets the portrait height of the
universal media.
Note:
If the value set exceeds the
maximum height, the MFP uses the
maximum value allowed in inches or
millimeters.
3–14.17 inches in
0.01 inch increments
76–360 mm in 1 mm
increments
Shows either inches or millimeters
from the Units of Measure setting;
14 inches is the US default, and
356 mm is the international default.
Feed Direction
Specifies the feed direction of the
Universal Paper Size.
Short Edge*
Long Edge
Feed Direction is only shown if the
Long Edge value is available. Long
Edge exists if the longest edge is
shorter than the maximum physical
width that the tray can accommodate.
See
Duplex Bind on page 70
for
more information about short and long
edges.