Lexmark X864 Card Stock & Label Guide - Page 119

Lexmark X850, X852e, and X854e

Get Lexmark X864 PDF manuals and user guides View all Lexmark X864 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

• Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your warranty. • If zone coating of the adhesive is not possible, a 3-mm (0.125-in.) strip should be removed on the leading and driver edge, and a non-oozing adhesive should be used. • Remove a 3-mm (0.125-in.) strip from the leading edge to prevent labels from peeling inside the printer. • Portrait orientation is preferred, especially when printing bar codes. • Do not use labels that have exposed adhesive. • Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. • Do not load a sheet of labels through the machine more than once. • Load labels into the multipurpose feeder with the recommended print side faceup and the top edge entering the printer first. When printing on card stock: • Set Paper Type to Card Stock from the printer driver. • Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components into the printer. • Do not use creased card stock. It may cause paper jams. • We recommend the use of grain short card stock. • Load card stock into the multipurpose feeder with the recommended print side faceup and the top edge entering the printer first. Lexmark X850, X852e, and X854e Limit label printing to occasional use of paper office labels designed for laser printers. Paper labels are supported in Tray 1, Tray 2, and the manual bypass feeder. The following table lists the maximum weights supported. Note: Scanning large quantities of labels is not recommended. Printer specifications 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
•
Do
not
use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive
at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your
warranty.
•
If zone coating of the adhesive is not possible, a 3-mm (0.125-in.) strip should be removed on the leading and driver
edge, and a non-oozing adhesive should be used.
•
Remove a 3-mm (0.125-in.) strip from the leading edge to prevent labels from peeling inside the printer.
•
Portrait orientation is preferred, especially when printing bar codes.
•
Do
not
use labels that have exposed adhesive.
•
Do
not
use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.
•
Do
not
load a sheet of labels through the machine more than once.
•
Load labels into the multipurpose feeder with the recommended print side faceup and the top edge entering the
printer first.
When printing on card stock:
•
Set Paper Type to Card Stock from the printer driver.
•
Do
not
use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting
introduces semi-liquid and volatile components into the printer.
•
Do
not
use creased card stock. It may cause paper jams.
•
We recommend the use of grain short card stock.
•
Load card stock into the multipurpose feeder with the recommended print side faceup and the top edge entering
the printer first.
Lexmark X850, X852e, and X854e
Limit label printing to occasional use of paper office labels designed for laser printers. Paper labels are supported in
Tray 1, Tray 2, and the manual bypass feeder.
The following table lists the maximum weights supported.
Note:
Scanning large quantities of labels is
not
recommended.
Printer specifications
119