Lexmark X864 Card Stock & Label Guide - Page 69

Media specifications, Set the Paper Type to Card Stock from the printer driver

Get Lexmark X864 PDF manuals and user guides View all Lexmark X864 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Media specifications Labels Width: 76.2-216 mm (3.0-8.5 in.) Length: 127-355.6 mm (5-14 in.) Weight: Up to 199 g/m2 (53 lb) Thickness: Up to 0.25 mm (0.01 in.) Smoothness: 100-400* Sheffield * 150-250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation. Card stock Weight: Up to 163 g/m2 Index Bristol (90 lb) Up to 163 g/m2 Tag (100 lb) Note: Always use the rear exit when printing on card stock. To minimize curl, use the rear exit when printing on labels. Card stock and label guidelines When printing on labels: • Set the Paper Type to Labels from the printer driver, the Local Printer Setup Utility, or MarkVision. • Do not load labels together with paper or transparencies in the same paper source. • Do not use label sheets with a slick backing material. • Do not print within 1 mm (0.040 in.) of the die-cut. • Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial sheets will also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge warranties. • Use labels that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. • Use labels that can withstand pressure of 25 pounds per square inch (psi). • Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label. • Do not use labels that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least 1 mm (0.040 in.) from the edges. Adhesive material will contaminate the printer and could void the warranty. • If zone coating of the adhesive is not possible, a 3-mm (0.125-in.) strip should be removed on the leading and driver edge, and a non-oozing adhesive should be used. • Remove a 3-mm (0.125-in.) strip from the leading edge to prevent labels from peeling inside the printer. • Portrait orientation is preferred, especially when printing bar codes. • Do not use labels that have exposed adhesive. • For the multipurpose feeder, load labels with the recommended print side faceup and the top edge going in first. For the tray, load labels with the recommended print side facedown. When printing on card stock: • Set the Paper Type to Card Stock from the printer driver, the Local Printer Setup Utility, or MarkVision. • Do not use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting introduces semi-liquid and volatile components into the printer. • Do not use card stock that is creased. It may cause paper jams. • We recommend the use of grain short card stock. • Load card stock with the recommended print side faceup and the top edge going in first. Printer specifications 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Media specifications
Labels
Width:
76.2–216 mm (3.0–8.5 in.)
Length:
127–355.6 mm (5–14 in.)
Weight:
Up to 199 g/m
2
(53 lb)
Thickness:
Up to 0.25 mm (0.01 in.)
Smoothness:
100–400* Sheffield
* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.
Card stock
Weight:
Up to 163 g/m
2
Index Bristol (90 lb)
Up to 163 g/m
2
Tag (100 lb)
Note:
Always use the rear exit when printing on card stock. To minimize curl, use the rear exit when printing on labels.
Card stock and label guidelines
When printing on labels:
•
Set the Paper Type to Labels from the printer driver, the Local Printer Setup Utility, or MarkVision.
•
Do
not
load labels together with paper or transparencies in the same paper source.
•
Do
not
use label sheets with a slick backing material.
•
Do
not
print within 1 mm (0.040 in.) of the die-cut.
•
Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial
sheets will also contaminate the printer and the cartridge with adhesive, and could void the printer and cartridge
warranties.
•
Use labels that can withstand temperatures of 205°C (401°F) without sealing, excessive curling, wrinkling, or
releasing hazardous emissions.
•
Use labels that can withstand pressure of 25 pounds per square inch (psi).
•
Do
not
print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.
•
Do
not
use labels that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least
1 mm (0.040 in.) from the edges. Adhesive material will contaminate the printer and could void the warranty.
•
If zone coating of the adhesive is not possible, a 3-mm (0.125-in.) strip should be removed on the leading and driver
edge, and a non-oozing adhesive should be used.
•
Remove a 3-mm (0.125-in.) strip from the leading edge to prevent labels from peeling inside the printer.
•
Portrait orientation is preferred, especially when printing bar codes.
•
Do
not
use labels that have exposed adhesive.
•
For the multipurpose feeder, load labels with the recommended print side faceup and the top edge going in first.
For the tray, load labels with the recommended print side facedown.
When printing on card stock:
•
Set the Paper Type to Card Stock from the printer driver, the Local Printer Setup Utility, or MarkVision.
•
Do
not
use preprinted card stock manufactured with chemicals that may contaminate the printer. Preprinting
introduces semi-liquid and volatile components into the printer.
•
Do
not
use card stock that is creased. It may cause paper jams.
•
We recommend the use of grain short card stock.
•
Load card stock with the recommended print side faceup and the top edge going in first.
Printer specifications
69