Lexmark X864 Card Stock & Label Guide - Page 120

Tray 1, Multipurpose feeder, releasing hazardous emissions.

Get Lexmark X864 PDF manuals and user guides View all Lexmark X864 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

Overview of card stock and label support Tray 1 Labels Card stock 64-105 g/m2 64-105 g/m2 Tray 2 64-216 g/m2 64-216 g/m2 Multipurpose feeder 64-216 g/m2 64-216 g/m2 Media specifications Labels Card stock Width: 89-297 mm (3.5-11.7 in.) Length: 99-432 mm (3.9-17 in.) Weight: 64-216 g/m2 Thickness: Up to 0.25 mm Smoothness: 100-400 Sheffield* * 150-250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation. Width: 89-297 mm (3.5-11.7 in.) Length: 99-432 mm (3.9-17 in.) Weight: Up to 216 g/m2 Use only materials recommended for use with laser printers. To prevent specialty media sheets from sticking together, remove each sheet from the output bin as it is printed. Card stock and label guidelines When printing on labels: • Set the Paper Type to Labels from the printer driver. • Use standard-size products (either A4 or Letter). • Do not use label sheets with a slick backing material. • Do not print within 1 mm (0.040 in.) of the die-cut. • Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge warranties. • Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or releasing hazardous emissions. • Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second. • Use labels that can withstand pressure of 25 pounds per square inch (psi). • Do not print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label. • Do not use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your warranty. • If zone coating of the adhesive is not possible, a 3-mm (0.125-in.) strip should be removed on the leading and driver edge, and a non-oozing adhesive should be used. • Remove a 3-mm (0.125-in.) strip from the leading edge to prevent labels from peeling inside the printer. • Portrait orientation is preferred, especially when printing bar codes. • Do not use labels that have exposed adhesive. Printer specifications 120

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Overview of card stock and label support
Tray 1
Tray 2
Multipurpose feeder
Labels
64–105 g/m
2
64–216 g/m
2
64–216 g/m
2
Card stock
64–105 g/m
2
64–216 g/m
2
64–216 g/m
2
Media specifications
Labels
Width:
89–297 mm (3.5–11.7 in.)
Length:
99–432 mm (3.9–17 in.)
Weight:
64–216 g/m
2
Thickness:
Up to 0.25 mm
Smoothness:
100–400 Sheffield*
* 150–250 Sheffield is optimal. Using media higher than 300 Sheffield could result in printing degradation.
Card stock
Width:
89–297 mm (3.5–11.7 in.)
Length:
99–432 mm (3.9–17 in.)
Weight:
Up to 216 g/m
2
Use only materials recommended for use with laser printers.
To prevent specialty media sheets from sticking together, remove each sheet from the output bin as it is printed.
Card stock and label guidelines
When printing on labels:
•
Set the Paper Type to Labels from the printer driver.
•
Use standard-size products (either A4 or Letter).
•
Do
not
use label sheets with a slick backing material.
•
Do
not
print within 1 mm (0.040 in.) of the die-cut.
•
Use full label sheets. Partial sheets may cause labels to peel off during printing, resulting in a paper jam. Partial
sheets will also contaminate your printer and your cartridge with adhesive, and could void your printer and cartridge
warranties.
•
Use labels that can withstand temperatures of 180°C (356°F) without sealing, excessive curling, wrinkling, or
releasing hazardous emissions.
•
Verify that your label adhesive material can tolerate a fusing temperature of 180°C (356°F) for 0.1 second.
•
Use labels that can withstand pressure of 25 pounds per square inch (psi).
•
Do
not
print within 1 mm (0.040 in.) of the edge of the label, of the perforations, or between die-cuts of the label.
•
Do
not
use label sheets that have adhesive to the edge of the sheet. We recommend zone coating of the adhesive
at least 1 mm (0.040 in.) away from edges. Adhesive material will contaminate your printer and could void your
warranty.
•
If zone coating of the adhesive is not possible, a 3-mm (0.125-in.) strip should be removed on the leading and driver
edge, and a non-oozing adhesive should be used.
•
Remove a 3-mm (0.125-in.) strip from the leading edge to prevent labels from peeling inside the printer.
•
Portrait orientation is preferred, especially when printing bar codes.
•
Do
not
use labels that have exposed adhesive.
Printer specifications
120