Home » Lexmark Manuals » Multifunction Devices » Lexmark X925 » Manual Viewer

Lexmark X925 Common Criteria Installation Supplement and Administrator Guide - Page 20

Security audit logging

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

20 3 Under Simple Kerberos Setup, for KDC Address, type the IP address or host name of the KDC (Key Distribution Center) IP. 4 For KDC Port, type the number of the port used by the Kerberos server. 5 For Realm, type the realm used by the Kerberos server. Note: The Realm entry must be typed in all uppercase letters. 6 Click Submit to save the information as a krb5.conf file. Note: Because only one krb5.conf file is used, uploading or submitting Simple Kerberos settings will overwrite the configuration file. Importing a Kerberos configuration file Using the EWS, you can also import a krb5.conf file rather than configure the Simple Kerberos Setup. 1 From the Embedded Web Server, click Settings > Security > Security Setup. Note: For information about accessing the EWS, see "Using the Embedded Web Server" on page 15. 2 Under Advanced Security Setup, at Step 1, click Kerberos 5. 3 Under Import Kerberos File, click Browse to navigate to your stored krb5.conf file. 4 Click Submit to upload the krb5.conf file. Note: After you click Submit, the device will automatically test the krb5.conf file to verify that it is functional. Notes: • Click Delete File to remove the Kerberos configuration file from the selected device. • Click View File to view the Kerberos configuration file for the selected device. • Click Test Setup to verify that the Kerberos configuration file for the selected device is functional. Using the touch screen Simple Kerberos settings can be configured or adjusted using the touch screen. 1 From the home screen, touch > Security > Edit Security Setups > Edit Building Blocks > Simple Kerberos Setup. 2 Type the KDC (Key Distribution Center) IP address or host name, and then touch Done. 3 Type the number of the port used by the Kerberos server, and then touch Done. 4 Type the realm used by the Kerberos server, and then touch Done. Note: The Realm entry must be typed in all uppercase letters. Security audit logging Using the EWS 1 From the Embedded Web Server, click Settings > Security > Security Audit Log. Note: For information about accessing the EWS, see "Using the Embedded Web Server" on page 15. 2 Select the Enable Audit check box.

Section	Page
Installation Supplement and Administrator Guide	1
Contents	3
Overview and first steps	5
Overview	5
Using this guide	5
Supported devices	5
Operating environment	6
Before configuring the device (required)	6
Verifying physical interfaces and installed firmware	6
Attaching a lock	7
Encrypting the hard disk	7
Disabling the USB buffer	8
Installing the minimum configuration	9
Configuring the device	9
Configuration checklist	9
Configuring disk wiping	9
Enabling the backup password (optional)	9
Creating user accounts	10
Creating security templates	11
Controlling access to device functions	12
Disabling home screen icons	14
Administering the device	15
Using the Embedded Web Server	15
Settings for network-connected devices	15
Creating and modifying digital certificates	15
Setting up IPSec	17
Disabling the AppleTalk protocol	18
Shutting down port access	18
Other settings and functions	19
Network Time Protocol	19
Kerberos	19
Security audit logging	20
E-mail	22
Fax	24
Configuring security reset jumper behavior	25
User access	25
Creating user accounts through the EWS	25
Configuring LDAP+GSSAPI	27
Configuring Common Access Card access	30
Creating security templates using the EWS	32
Controlling access to device functions	33
Configuring PKI Held Jobs	33
Controlling access to device functions using the EWS	34
Troubleshooting	37
Login issues	37
“Unsupported USB Device” error message	37
Make sure a supported Smart Card reader is attached	37
The printer home screen fails to return to a locked state when not in use	37
Make sure the authentication token is installed and running	37
Make sure PKI Authentication is installed and running	37
Login screen does not appear when a Smart Card is inserted	37
Make sure the Smart Card is recognized by the reader	37
“The KDC and MFP clocks are different beyond an acceptable range; check the MFP's date and time” err ...	38
Verify the date and time on the printer	38
“Kerberos configuration file has not been uploaded” error message	38
Make sure the Kerberos file has been uploaded	38
Users are unable to authenticate	38
Make sure the Realm specified in the Kerberos settings is in uppercase	38
“The Domain Controller Issuing Certificate has not been installed” error message	39
Make sure that the correct certificate has been installed on the printer	39
“The KDC did not respond within the required time” error message	39
Make sure the IP address or host name of the KDC is correct	39
Make sure the KDC is available	39
Make sure Port 88 is not blocked by a firewall	39
“User's Realm was not found in the Kerberos Configuration file” error message	39
Make sure the Windows Domain is specified in the Kerberos settings	39
“Realm on the card was not found in the Kerberos Configuration File” error message	40
Upload a Kerberos configuration file and make sure the realm has been added to the file	40
“Client [NAME] unknown” error message	40
Verify that the Domain Controller information is correct	40
Login does not respond at “Getting User Info”	40
User is logged out almost immediately after logging in	40
Increase the Panel Login Timeout interval	40
LDAP issues	41
LDAP lookups take a long time and then fail	41
Make sure Port 389 (non-SSL) and Port 636 (SSL) are not blocked by a firewall	41
Make sure the LDAP search base is not too broad in scope	41
LDAP lookups fail almost immediately	41
Verify that the Address Book Setup contains the host name for the LDAP server	41
Verify or adjust Address Book Setup settings	41
Narrow the LDAP search base	41
Verify that the LDAP attributes being searched for are correct	41
Held Jobs/Print Release Lite issues	42
“You are not authorized to use this feature” Held Jobs error message	42
Add the user to the appropriate Active Directory group	42
“Unable to determine Windows User ID” error message	42
Make sure PKI Authentication is setting the user ID for the session	42
“There are no jobs available for [USER]” error message	42
Make sure PKI Authentication is setting the correct user ID	42
Make sure the jobs were sent to the correct printer and were printed	42
Jobs are printing out immediately	43
Make sure PKI Held Jobs is installed and running	43
Make sure all jobs are required to be held	43
Appendix A: Using the touch screen	44
Appendix B: Acronyms	46
Appendix C: Description of access controls	47
Access controls	47
Appendix D: Using Common Access Cards	50
Using a Common Access Card to access the printer	50
Notices	51
LEXMARK SOFTWARE LICENSE AGREEMENT	51

Match case Limit results 1 per page

Under Simple Kerberos Setup, for KDC Address, type the IP address or host name of the KDC (Key Distribution

Center) IP.

For KDC Port, type the number of the port used by the Kerberos server.

For Realm, type the realm used by the Kerberos server.

Note:

The Realm entry must be typed in all uppercase letters.

Click

Submit

to save the information as a krb5.conf file.

Note:

Because only one krb5.conf file is used, uploading or submitting Simple Kerberos settings will overwrite the

configuration file.

Importing a Kerberos configuration file

Using the EWS, you can also import a krb5.conf file rather than configure the Simple Kerberos Setup.

From the Embedded Web Server, click

Settings

Security

Security Setup

Note:

For information about accessing the EWS, see “Using the Embedded Web Server” on page 15.

Under Advanced Security Setup, at Step 1, click

Kerberos 5

Under Import Kerberos File, click

Browse

to navigate to your stored krb5.conf file.

Click

Submit

to upload the krb5.conf file.

Note:

After you click

Submit

, the device will automatically test the krb5.conf file to verify that it is functional.

Notes:

•

Click

Delete File

to remove the Kerberos configuration file from the selected device.

•

Click

View File

to view the Kerberos configuration file for the selected device.

•

Click

Test Setup

to verify that the Kerberos configuration file for the selected device is functional.

Using the touch screen

Simple Kerberos settings can be configured or adjusted using the touch screen.

From the home screen, touch

Security

Edit Security Setups

Edit Building Blocks

Simple Kerberos Setup

Type the KDC (Key Distribution Center) IP address or host name, and then touch

Done

Type the number of the port used by the Kerberos server, and then touch

Done

Type the realm used by the Kerberos server, and then touch

Done

Note:

The Realm entry must be typed in all uppercase letters.

Security audit logging

Using the EWS

From the Embedded Web Server, click

Settings

Security

Security Audit Log

Note:

For information about accessing the EWS, see “Using the Embedded Web Server” on page 15.

Select the

Enable Audit

check box.