LiftMaster CSW24VDC CSW24VDC Installation Manual - Page 49

STEP 8 continued...3, the other solar panel.

Get LiftMaster CSW24VDC PDF manuals and user guides View all LiftMaster CSW24VDC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

APPENDIX STEP 8 continued... SOLAR PANEL(S) INSTALL THE SOLAR PANEL 1. Position solar bracket on mounting surface. Mark and drill holes. 2. Insert two bolts into the track located on the back of the solar panel(s). 3. Slide bolts in track away from bolt hole and align both bolts. 4. Secure solar panel(s) to solar bracket using two washered nuts. 5. Secure solar panel(s) assembly to mounting surface using appropriate hardware. Mounting Surface Mounted Panel Must Face South Mounting Surface WIRE THE SOLAR PANELS 1. Locate the J15 plug on the control board and unplug it from the control board (it will not be used). 2. Install the new 33AH batteries using the tray as shown. 3. Connect the white jumper between the positive (+) terminal of one battery to the negative terminal (-) of the other battery. 4. Route the battery wires (the longer set of wires) from the J15 plug (new wire harness) through the lower, right, rear knockout (KO) in the electrical box. Use the included adhesive wire clamps to route the wires up the right side of the operator frame. Connect the red wire to J15 Plug the positive (+) terminal of one battery. Connect the black wire to the (new wire harness, negative (-) terminal of the other battery. Model K94-37236) 5. Connect the red wire (+) from one solar panel to the black wire (-) of the other solar panel. Black Wire (-) Diode + 6. Connect the shorter red wire (+) from the J15 plug (new wire harness) labeled DC Power to the red wire on one solar panel. Connect the shorter black (-) wire from the J15 plug (new wire harness) labeled DC Power to the black wire from the other solar panel. - + - 7. Plug the J15 plug (new wire harness) into the J15 input on the control board. NOTE: You may see a small spark when plugging the J15 plug into the board. 40W Solar panel installation Proceed to the Dual Gate section (if applicable) or proceed to the Adjustment section. 48 33AH Batteries - +- + Black Wire (-) Red Wire (+) Red Wire (+) + + - - + + - - 60W Solar panel installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
48
Black Wire (-)
33AH Batteries
Red Wire (+)
J15 Plug
(new wire harness,
Model K94-37236)
+
+
+
+
+
+
–
–
–
–
–
–
–
+
–
+
Red Wire (+)
Black Wire (-)
Mounted Panel
Must Face South
Mounting Surface
Mounting Surface
APPENDIX
STEP 8 continued...
SOLAR PANEL(S)
INSTALL THE SOLAR PANEL
1.
Position solar bracket on mounting surface. Mark and drill holes.
2.
Insert two bolts into the track located on the back of the solar
panel(s).
3. Slide bolts in track away from bolt hole and align both bolts.
4.
Secure solar panel(s) to solar bracket using two washered nuts.
5.
Secure solar panel(s) assembly to mounting surface using appropriate
hardware.
WIRE THE SOLAR PANELS
1.
Locate the J15 plug on the control board and unplug it from the
control board (it will not be used).
2.
Install the new 33AH batteries using the tray as shown.
3.
Connect the white jumper between the positive (+) terminal of one
battery to the negative terminal (-) of the other battery.
4.
Route the battery wires (the longer set of wires) from the J15 plug
(new wire harness) through the lower, right, rear knockout (KO) in the
electrical box. Use the included adhesive wire clamps to route the
wires up the right side of the operator frame. Connect the red wire to
the positive (+) terminal of one battery. Connect the black wire to the
negative (-) terminal of the other battery.
5.
Connect the red wire (+) from one solar panel to the black wire (-) of
the other solar panel.
6.
Connect the shorter red wire (+) from the J15 plug (new wire
harness) labeled DC Power to the red wire on one solar panel.
Connect the shorter black (-) wire from the J15 plug (new wire
harness) labeled DC Power to the black wire from the other solar
panel.
7.
Plug the J15 plug (new wire harness) into the J15 input on the control
board.
NOTE:
You may see a small spark when plugging the J15 plug
into the board.
Proceed to the Dual Gate section (if applicable) or proceed to the
Adjustment section.
40W Solar panel
installation
60W Solar panel
installation
Diode