Netgear WGR614v9 WGR614v9 User Manual - Page 44

Configuring a User-Defined Service, Service Type, User Defined - range

Get Netgear WGR614v9 - 54 Mbps Wireless Router PDF manuals and user guides View all Netgear WGR614v9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Wireless-G Router WGR614v9 Reference Manual To block by schedule, be sure to specify a time period in the Schedule screen. For information about scheduling, see "Scheduling Blocking" on page 3-5. 3. Specify a service for blocking by clicking Add. The Block Services Setup screen displays. Figure 3-3 4. From the Service Type list, select the application or service to be allowed or blocked. The list already displays several common services, but you are not limited to these choices. To add any additional services or applications that do not already appear, select User Defined. 5. Select the radio button for the IP address configuration you want to block, and then enter the IP addresses in the appropriate fields. 6. Click Add to enable your Block Services Setup selections. Configuring a User-Defined Service To define a service, first you must determine which port number or range of numbers is used by the application. The service port numbers for many common protocols are defined by the Internet Engineering Task Force (IETF) and published in RFC1700, "Assigned Numbers." Service numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of the application. You can often determine port number information by contacting the publisher of the application, by asking user groups or newsgroups, or by searching. • Enter the starting port and ending port numbers. If the application uses a single port number, enter that number in both fields. 3-4 Restricting Access From Your Network v1.1, May 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Wireless-G Router WGR614v9 Reference Manual
3-4
Restricting Access From Your Network
v1.1, May 2008
To block by schedule, be sure to specify a time period in the Schedule screen. For information
about scheduling, see
“Scheduling Blocking” on page 3-5
.
3.
Specify a service for blocking by clicking
Add
. The Block Services Setup screen displays.
4.
From the
Service Type
list, select the application or service to be allowed or blocked. The list
already displays several common services, but you are not limited to these choices. To add any
additional services or applications that do not already appear, select
User Defined
.
5.
Select the radio button for the IP address configuration you want to block, and then enter the
IP addresses in the appropriate fields.
6.
Click
Add
to enable your Block Services Setup selections.
Configuring a User-Defined Service
To define a service, first you must determine which port number or range of numbers is used by
the application. The service port numbers for many common protocols are defined by the Internet
Engineering Task Force (IETF) and published in RFC1700, “Assigned Numbers.” Service
numbers for other applications are typically chosen from the range 1024 to 65535 by the authors of
the application. You can often determine port number information by contacting the publisher of
the application, by asking user groups or newsgroups, or by searching.
•
Enter the starting port and ending port numbers. If the application uses a single port number,
enter that number in both fields.
Figure 3-3