Oki C710n Network User's Guide, English - Page 69

Overview Configuration

Get Oki C710n PDF manuals and user guides View all Oki C710n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

UNIX NOTE: 1. This section does not apply to GDI printers. 2. Not all utilities are supported by every operating system. Please check with your User's Guide and your support website for latest information. OVERVIEW The printer supports many protocols such as LPD, FTP, TELNET, SNMP and IPP, and works within the UNIX environment. To use the network card within the UNIX environment, the following steps are required: CONFIGURATION NETWORK INTERFACE CARD SETTING The first step in installing the network card under UNIX is to set up the IP address, Subnet Mask and Gateway. This section explains one way to set them up from a UNIX workstation. > The network addresses used in this manual are shown as examples only. Network addresses used in your installation must be generated for your own network. > Log in as root to change the configuration of the printer. > If an incorrect IP address, Subnet Mask or Gateway is entered, the network may go down or other damage may occur. Check the address with your network manager. The following explanation uses Sun Solaris 2.8 (Solaris 8) as an example. The actual commands may differ between versions of UNIX, so refer to the workstation manuals for more information. NOTE: If you do not have superuser rights, the network manger should conduct the configuration. 1. Log in as root to the workstation. UNIX > 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
UNIX > 69
UNIX
O
VERVIEW
The printer supports many protocols such as LPD, FTP, TELNET,
SNMP and IPP, and works within the UNIX environment.
To use the network card within the UNIX environment, the
following steps are required:
C
ONFIGURATION
N
ETWORK
I
NTERFACE
CARD
SETTING
The first step in installing the network card under UNIX is to set
up the IP address, Subnet Mask and Gateway. This section
explains one way to set them up from a UNIX workstation.
>
The network addresses used in this manual are shown as
examples only. Network addresses used in your
installation must be generated for your own network.
>
Log in as root to change the configuration of the printer.
>
If an incorrect IP address, Subnet Mask or Gateway is
entered, the network may go down or other damage may
occur. Check the address with your network manager.
The following explanation uses Sun Solaris 2.8 (Solaris 8) as an
example. The actual commands may differ between versions of
UNIX, so refer to the workstation manuals for more information.
1.
Log in as root to the workstation.
NOTE:
1.
This section does not apply to GDI printers.
2.
Not all utilities are supported by every operating
system. Please check with your User’s Guide and
your support website for latest information.
NOTE:
If you do not have superuser rights, the network manger
should conduct the configuration.