Onkyo TX-NR3009 Owner Manual - Page 34
Audyssey MultEQ XT32 Full Calibration., Audyssey Quick Start - review
View all Onkyo TX-NR3009 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 34 highlights
3 When you've finished making the settings, press ENTER. MultEQ XT32: Auto Setup Speakers Type(Front A) Speakers Type(Front B) Powered Zone 2 Powered Zone 3 AUDYSSEY Normal No No No Perform the "Speaker Setup" according to your speaker configuration: - Speakers Type(Front A) (➔ page 51) - Speakers Type(Front B) (➔ page 51) - Powered Zone 2 (➔ page 51) - Powered Zone 3 (➔ page 51) - Front High + Front Wide (➔ page 51) - Subwoofer (➔ page 52) If you are using a subwoofer(s), select "1ch" or "2ch" in the "Subwoofer" setting (➔ page 52). If not, select "No" and skip step 4. When an optional unit is connected to the UNIVERSAL PORT jack on the AV receiver, the optional unit setting may appear on the speaker setting menu. 4 Adjust the subwoofer volume level to 75 dB, and then press ENTER. Test tones are played through the subwoofer. Use the volume control on the subwoofer. When the "Subwoofer" setting is set to "1ch" only, the left-hand subwoofer (SW1) will be measured. When the "Subwoofer" setting is set to "1ch" with two subwoofers connected, the right-hand subwoofer (SW2) will not be measured and no sound will be output. An error will occur if you set "Subwoofer" to "2ch" without connecting any subwoofers, or with only one subwoofer connected. Note • If your subwoofer does not have a volume control, disregard the displayed level and press ENTER to proceed to the next step. • If you set the subwoofer's volume control to its maximum and the level displayed is lower than 75 dB, leave the subwoofer's volume control at its maximum and press ENTER to proceed to the next step. • If you use two subwoofers, perform this step twice. 5 Use R/X to select "Audyssey Quick Start" or "Audyssey MultEQ XT32 Full Calibration". En 34 6 Press ENTER. Audyssey MultEQ® XT32 Room Correction and Speaker Setup starts. Test tones are played through each speaker as Audyssey MultEQ XT32 Room Correction and Speaker Setup runs. This process takes a few minutes. Please refrain from talking during measurements and do not stand between speakers and the microphone. Do not disconnect the speaker setup microphone during Audyssey MultEQ XT32 Room Correction and Speaker Setup, unless you want to cancel the setup. If you select "Audyssey Quick Start", you will go to step 9. 7 Place the speaker setup microphone at the next position, and then press ENTER. Audyssey MultEQ XT32 performs more measurements. This takes a few minutes. 8 When prompted, repeat step 7. 9 Use R/X to select an option, and then press ENTER. MultEQ XT32: Auto Setup Subwoofer Front Center Surround Front Wide Front High Surround Back Surround Back Ch -- Review Speaker Configuration -- 2ch 40Hz 40Hz 100Hz None 100Hz 120Hz 2ch Save Cancel AUDYSSEY The options are: ` Save: Save the calculated settings and exit Audyssey MultEQ XT32 Room Correction and Speaker Setup. ` Cancel: Cancel Audyssey MultEQ XT32 Room Correction and Speaker Setup. Tip • You can view the calculated settings for the speaker configuration, speaker distances, and speaker levels by using F/S. 10 Use R/X to select a target, and use F/S to change the setting. After the results of Audyssey MultEQ XT32 have been saved, the menu will display the "Audyssey" (➔ page 58), "Dynamic EQ" (➔ page 59), "Dynamic Volume" (➔ page 59) settings. Note • When "Audyssey Quick Start" has been used for measurement, "Audyssey" cannot be selected. • These settings are applied to all input selectors. 11 Press ENTER. 12 Disconnect the speaker setup microphone.