Panasonic AW-HN38H AW-HN38H Operating Instructions - Page 72
Transmission type, Unicast port Image, Multicast address, Multicast port, Multicast TTL/HOP Limit
View all Panasonic AW-HN38H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 72 highlights
Web screen configurations (continued) Transmission type Select the transmission format for H.264 images. Setting value: Unicast port (AUTO) Up to 14 users can access a single camera at the same time. [Unicast port (Image)] and [Unicast port (Audio)] will be configured automatically when images and audio are sent from the camera. We recommend selecting the [Unicast port (MANUAL)] setting when the port number transmitting the H.264 images does not need to be fixed (e.g., during use within a network). Unicast port (MANUAL) Up to 14 users can access a single camera at the same time. [Unicast port (Image)] and [Unicast port (Audio)] must be configured manually when images and audio are sent from the camera. When transmitting H.264 images via the Internet, configure a fixed transmission port for the broadband router (hereafter referred to as "router") (page 90). For details, refer to the operating instructions for the router. Multicast An unlimited number of users can access a single camera at the same time. When transmitting H.264 images via multicast, enter the [Multicast address], [Multicast port], and [Multicast TTL/HOPLimit]. Factory settings: Unicast port (AUTO) Note ●● For details on the maximum number for simultaneous access, see page 56. Unicast port (Image) Enter the unicast port number (used when sending images from the unit). Usable port number range: 1024 to 50000 ●● Only even numbers can be specified. ●● The port number cannot be set to 10670. Factory settings: H.264(1): 32004 H.264(2): 32014 H.264(3): 32024 H.264(4): 32034 Unicast port (Audio) Usable port number range: 1024 to 50000 ●● Only even numbers can be specified. ●● The port number cannot be set to 10670. Factory settings: H.264(1): 33004 H.264(2): 33014 H.264(3): 33024 H.264(4): 33034 Note ●● The unicast port number must be configured when [Transmission type] is set to [Unicast port (MANUAL)]. Multicast address Enter the multicast IP address. Images and audio will be sent to the specified IP address. Usable values: IPv4: 224.0.0.0 to 239.255.255.255 IPv6: Multicast address starting with FF. Factory settings: H.264(1): 239.192.0.20 H.264(2): 239.192.0.21 H.264(3): 239.192.0.22 H.264(4): 239.192.0.23 Note ●● Verify usable multicast IP addresses before entering this setting. Multicast port Enter the multicast port number (used when sending images from the unit). Usable port number range: 1024 to 50000 ●● Only even numbers can be specified. ●● The port number cannot be set to 10670. Factory settings: 37004 Note ●● When sending audio from the unit, a port number with "1000" added to the multicast port number will be used. Multicast TTL/HOP Limit Enter the TTL/HOPLimit value for multicast. Usable values: 1 to 254 Factory settings: 16 Notes ●● When transmitting H.264 images via the Internet, transmitted images may not appear depending on proxy server settings, firewall settings, etc. In such cases, consult your network administrator. ●● When displaying multicast images on a personal computer with multiple LAN cards installed, disable the LAN cards that are not used for reception. Note ●● IP control can be performed but if you do not want to perform IP image transmission, set "JPEG transmission", "H.264 transmission" and "Audio Transmission" to "Off". In this case, IP images will also not be displayed on the mobile terminal. 72