Panasonic AW-HN38H AW-HN38H Operating Instructions - Page 78
Detail, Detail Level H, Flesh Tone Mode, Notes, Pedestal, Setting value, Factory settings
View all Panasonic AW-HN38H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 78 highlights
Web screen configurations (continued) Detail The image detail (image sharpness) is adjusted here. When "Low" or "High" is selected, the detail is enhanced. Setting value: Off, Low, High Factory settings: Low Detail Level H The image sharpness level is adjusted here when "High" has been selected as the "Detail" setting. Setting range: Detail Level L setting +1 to 18 Factory settings: 18 Detail Level L The image sharpness level is adjusted here when "Low" has been selected as the "Detail" setting. Setting range: 1 to Detail Level H setting -1 Factory settings: 9 Flesh Tone Mode Set here is the flesh tone mode for displaying the subjects' skin so that it appears more smoothly and eye‑pleasingly. When "Low" or "High" is selected, the effect is enhanced. Setting value: Off, Low, High Factory settings: Off HDR Adjust the effect of the high dynamic range mode. When HDR is set to "Low", correction is performed so that the appropriate exposure is obtained for the light and dark areas on subjects with extremely high contrast. When "High" is selected, dark areas are made brighter. Depending on the shooting conditions, however, the picture quality may drop with increased noise. In addition, unit vibration may result in blurry or distorted images. This effect is not recommended in shooting locations where significant vibration may occur. Setting value: Off, Low, High Factory settings: Off Notes ●● When the HDR setting is changed, the monitor images will go momentarily black and the audio will be muted. Furthermore, IP video may stop for about 30 seconds. ●● When "Low" or "High" is selected, it will take longer for the brightness of the image to converge. ●● When "Low" or "High" is selected, brightness cannot be adjusted. ●● When "Low" or "High" is selected, video will be delayed by 4 frames. ●● When "Low" or "High" is selected, the following settings cannot be changed. • Day/Night • Night-Day Level • Pedestal • DRS • Gamma Type • Back Light COMP. • Freeze During Preset • Image Stabilizer Notes ●● When "Low" or "High" is selected, the OSD menu cannot be displayed for the video on the Web screen. However, the OSD menu can be displayed over video output to a monitor. ●● If you attempt to display the OSD menu on the Web screen when "Low" or "High" is set, the HDR item becomes bar display and the setting cannot be changed. Change the setting from the Web setting screen, infrared remote control, etc. ●● When the priority mode (page 44, page 65) is "IP" mode and when HDR is set to "Low" or "High", there are the following restrictions. • JPEG(1) to (3): Fixed to 640×360. • H.264(1): 1280×720 cannot be used. • H.264(2) to (4): Cannot be used. ●● When the Priority Mode (page 44, page 65) selection is "NDI|HX", this item is fixed to "Off". DNR Set here is the level of the digital noise reduction effect so that light, noise-free and clear images will be output even at night and in other low-brightness environments. When "Low" or "High" is selected, noise can be eliminated. However, there is an increased possibility that afterimages may occur. Setting value: Off, Low, High Factory settings: Low Pedestal This item is used to adjust the black level (adjust the pedestal) so that the dark parts of the images are easier to see. These parts become darker when a negative setting is selected and, conversely, lighter when a positive setting is selected. Setting range: -10 to +10 Factory settings: 0 DRS Set here is the DRS function which provides just the right amount of compensation when images with significant light/dark differences are displayed. When "Low" or "High" is selected, the effect is enhanced even more. Depending on the shooting conditions, however, the picture quality may drop with increased noise. Setting value: Off, Low, High Factory settings: Off 78