Panasonic AW-HN40H AW-HN38H Operating Instructions - Page 40

Parts and their functions, Camera unit

Get Panasonic AW-HN40H PDF manuals and user guides View all Panasonic AW-HN40H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Parts and their functions ■■Camera unit aMount bracket for installation surface (supplied accessory) Mount this bracket onto the installation surface, and then attach the camera main unit to the bracket. bDrop-prevention wire Pull out the wire from the bottom panel of the camera main unit, and attach it to the hook of the mount bracket. cHole for securing the camera pedestal This hole is provided in the bottom panel of the camera pedestal. dWireless remote control signal light-sensing area Light sensors are located in four places; at the front of the camera pedestal and on either side.  eStatus display lamp This lights in the following way depending on the status of the unit. Orange: When the standby status is established Green: When the power is on Red: When trouble has occurred in the unit Green and blinks twice: When a signal matched by the remote control ID has been received from the wireless remote control (optional accessory) while the power is on Orange and blinks twice: When a signal which is not matched by the remote control ID has been received from the wireless remote control (optional accessory) while the power is on   fCamera head This rotates in the horizontal direction. gLens unit This rotates in the up and down direction. hTally lamp This comes on or goes off in response to the control from the controller but only when "On" has been selected as the tally lamp use setting.   40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
40
Parts and their functions
■
Camera unit
<Rear panel>
<Bottom panel>
a
Mount bracket for installation surface
(supplied accessory)
Mount this bracket onto the installation surface, and then
attach the camera main unit to the bracket.
b
Drop-prevention wire
Pull out the wire from the bottom panel of the camera
main unit, and attach it to the hook of the mount bracket.
c
Hole for securing the camera pedestal
This hole is provided in the bottom panel of the camera
pedestal.
d
Wireless remote control signal light-sensing
area
Light sensors are located in four places; at the front of the
camera pedestal and on either side.
e
Status display lamp
This lights in the following way depending on the status of
the unit.
Orange:
When the standby status is established
Green:
When the power is on
Red:
When trouble has occurred in the unit
Green and blinks twice:
When a signal matched by the remote control
ID has been received from the wireless remote
control (optional accessory) while the power is
on
Orange and blinks twice:
When a signal which is not matched by the
remote control ID has been received from the
wireless remote control (optional accessory)
while the power is on
f
Camera head
This rotates in the horizontal direction.
g
Lens unit
This rotates in the up and down direction.
h
Tally lamp
This comes on or goes off in response to the control from
the controller but only when “On” has been selected as the
tally lamp use setting.