Panasonic AW-HN40H AW-HN38H Operating Instructions - Page 6

Installation precautions Panasonic does not accept any responsibility for accident or damage during installation if procedure in this manual is not followed. To installation personnel Read the "Installation Instructions" thoroughly and then perform the operation correctly and safely. Also, always read the "Read this first!" (page 5) of this manual as they contain important information. After the installation, give the "Operating Instructions " to the customer to save for future use. Ensure that the installation work complies with the technical standards governing electrical equipment. The unit is for indoor use only. It cannot be used outdoors. Avoid installation in a location where the unit will be exposed to direct sunlight for extended periods or near a cooling or heating appliance. Otherwise, deformation, discoloration, malfunctioning and/or problems in operation may result. Operate the unit where it will not be splashed or sprayed by water. Use the unit with an installation where the unit is suspended from an overhead surface or with a stand‑alone installation. Do not use the unit on its side or tilted at an angle. Notes ●● Be absolutely sure to use the four bracket mounting screws (M4) for mounting the mount bracket. These are supplied with the unit. Do not use wood screws, nails, etc. In the case of a concrete ceiling, secure the unit using anchor bolts (for M4) or AY plug bolts (for M4). Recommended clamping torque M4: 1.47 N · m {15 kgf · cm} ●● The withdrawal strength of the mounting location for each screw must be at least 196 N {20 kgf}. ●● When mounting the unit on a ceiling made of plasterboard, for instance, if it is not strong enough to support its weight, either reinforce the ceiling adequately or use the WV‑Q105A direct ceiling mount bracket, which is sold separately. ●● When using a mount bracket which is sold separately, read the handling instructions. ●● Do not hold the camera head while undertaking the installation work. Doing so may cause malfunctioning. Correct Incorrect Correct Incorrect Desktop installation Hanging installation Concerning the installation location Install the unit in a stable location which will not be susceptible to shaking. If the unit is installed in a location which is susceptible to shaking, this will cause the unit's images to shake in turn. Install the unit after conferring in detail with your dealer. Install the unit on a ceiling that is strong enough (such as a concrete ceiling). If the unit is to be installed on a ceiling which is not strong enough, reinforce the ceiling sufficiently first. Do not install or use the unit in the following kinds of locations. ●● On walls (where the unit would be installed sideways) ●● In locations (including places such as under the eaves of a building) where the unit would be directly exposed to rain or water ●● In locations such as kitchens where there are high concentrations of steam and grease ●● In outdoor locations or hot places where the temperature will exceed 40 °C (104 °F) ●● In cold locations where the temperature will drop below 0 °C (32 °F) ●● In locations where the humidity will exceed 90% ●● In locations where chemicals are used such as near swimming pools ●● At sea, in coastal areas or in locations where corrosive gases are emitted ●● In locations where radiation, X-rays, or strong radio waves or magnetic fields are generated ●● In locations where the unit would be subject to a great deal of vibration such as on board a vehicle or ship (the unit is not designed to be used in vehicles) ●● In locations where the temperature is subject to sudden changes such as near the air outlet of an air conditioner or near a door which allows the outside air to come in What to avoid to ensure that the unit will perform stably over a prolonged period ●● Using the unit for a prolonged period in a location with high temperature and humidity levels will cause its parts to deteriorate and shorten its service life. ●● Ensure that a cooling unit or heating unit will not blow any air directly toward the installation location. AW‑HN40/ AW‑HN38 main unit Mass Approx. 1.5 kg [3.30 lb] 6 Mounting conditions Applicable mount bracket Mounting onto the ceiling Model No. Direct mount (supplied accessory) WV‑Q105A (optional accessory) Mass Approx. 0.23 kg [0.51 lb] Approx. 0.15 kg [0.33 lb] Mounting Hanging/Desktop For ceiling Recommended screws M4 screws (supplied accessory) M4 screws (supplied with the WV‑Q105A) No. of Minimum withdrawal strength screws (per screw) 196 N {20 kgf} 4 ●● Ensure that the mounting strength can support a weight that is at least five times the total mass 4 of the equipment, including the camera's main unit.