Panasonic BT-3DL2550 Operating Instructions - Page 32

System Config, B.light/cont., Backlight, Position, Status, Display, Setup Load, Setup Save, Power

Get Panasonic BT-3DL2550 PDF manuals and user guides View all Panasonic BT-3DL2550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Main Menu (continued) SYSTEM CONFIG Sub menu Settings B.LIGHT/CONT. BACKLIGHT CONTRAST BACKLIGHT MENU POSITION 0 - 50 - 60 CENTER LB RB RT LT STATUS DISPLAY OFF 3SEC OFF *3 CONTINUE SETUP LOAD SETUP SAVE POWER ON SETUP POWER SAVE MODE USER5 *1*2 USER4 *1*2 USER3 *1*2 USER2 *1*2 USER1 *1*2 FACTORY USER5 *2 USER4 *2 USER3 *2 USER2 *2 USER1 *2 USER5 USER4 USER3 USER2 USER1 FACTORY LAST OFF ON CALIBRATION Underlined values indicate factory defaults. Description Selects function to be assigned to BACKLIGHT/CONT. in the picture/ volume adjusting menu. Adjusts the BACKLIGHT. Adjusts the CONTRAST. Adjusts the backlight when the B.LIGHT/CONT. submenu is set to CONTRAST. Positions the on-screen menu. Center of the screen Left Bottom Right Bottom Right Top Left Top Sets display state for input signal status (on-screen menu). Not displayed. Displayed for 3 seconds after a status change. Displayed at all times Loads saved factory defaults (FACTORY) or user data (USER1 - USER5). After loading user data, the screen displays the signal selected before user data was loaded. Up to 5 sets of user data can be saved (J page 22). They save menu settings and adjustments made in the picture/volume adjusting menu (PHASE/CHROMA/BRIGHT/CONTRAST/BACKLIGHT) except "SETUP SAVE/SETUP LOAD." Selects the settings used when the power is turned on. Starts in the mode used when the power was last turned off. Starts up using the factory defaults. Starts up using USER registered settings. Sets the power save mode Does not activate the POWER SAVE mode. The backlight dims when no signal (NO SIGNAL) is input for 60 seconds or longer. Signal input or menu operation will return the backlight to its normal brightness. Connect a CA-210 color analyzer and use this submenu to make a calibration. It also returns calibration data to factory defaults. (J page 33, 34) *1 When the monitor is shipped, settings for "USER1" - "USER5" are identical to "FACTORY." *2 "H SHIFT" (J page 24), "H POSITION", "V POSITION", "PHASE" and "CLOCK" (J page 41) cannot be saved or loaded. *3 So that there is no confusion with 2D mode when working in 3D mode, STATUS DISPLAY will display information as per the "CONTINUE" setting even if "3SEC OFF" is selected. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
32
Main Menu
(continued)
Underlined values indicate factory defaults.
*1 When the monitor is shipped, settings for “USER1” - “USER5” are identical to “FACTORY.”
*2 “H SHIFT” (
J
page 24), “H POSITION”, “V POSITION”, “PHASE” and “CLOCK” (
J
page 41) cannot be saved
or loaded.
*3
So that there is no confusion with 2D mode when working in 3D mode, STATUS DISPLAY will display
information as per the “CONTINUE” setting even if “3SEC OFF” is selected.
SYSTEM CONFIG
Sub menu
Settings
Description
B.LIGHT/CONT.
BACKLIGHT
CONTRAST
Selects function to be assigned to BACKLIGHT/CONT. in the picture/
volume adjusting menu.
<BACKLIGHT>
Adjusts the BACKLIGHT.
<CONTRAST>
Adjusts the CONTRAST.
BACKLIGHT
0 - 50
- 60
Adjusts the backlight when the B.LIGHT/CONT. submenu is set to
CONTRAST.
MENU
POSITION
CENTER
LB
RB
RT
LT
Positions the on-screen menu.
<CENTER>
Center of the screen
<LB>
Left Bottom
<RB>
Right Bottom
<RT>
Right Top
<LT>
Left Top
STATUS
DISPLAY
OFF
3SEC OFF
*
3
CONTINUE
Sets display state for input signal status (on-screen menu).
<OFF>
Not displayed.
<3SEC OFF>
Displayed for 3 seconds after a status change.
<CONTINUE>
Displayed at all times
SETUP LOAD
USER5
*1*2
USER4
*1*2
USER3
*1*2
USER2
*1*2
USER1
*1*2
FACTORY
Loads saved factory defaults (FACTORY) or user data (USER1 - USER5).
After loading user data, the screen displays the signal selected before
user data was loaded.
SETUP SAVE
USER5
*2
USER4
*2
USER3
*2
USER2
*2
USER1
*2
Up to 5 sets of user data can be saved (
J
page 22).
They save menu settings and adjustments made in the picture/volume
adjusting menu (PHASE/CHROMA/BRIGHT/CONTRAST/BACKLIGHT)
except “SETUP SAVE/SETUP LOAD.”
POWER ON
SETUP
USER5
USER4
USER3
USER2
USER1
FACTORY
LAST
Selects the settings used when the power is turned on.
<LAST>
Starts in the mode used when the power was last turned
off.
<FACTORY>
Starts up using the factory defaults.
<USER1 - 5>
Starts up using USER registered settings.
POWER SAVE
MODE
OFF
ON
Sets the power save mode
<OFF>
Does not activate the POWER SAVE mode.
<ON>
The backlight dims when no signal (NO SIGNAL) is input for 60
seconds or longer. Signal input or menu operation will return the
backlight to its normal brightness.
CALIBRATION
Connect a CA-210 color analyzer and use this submenu to make a
calibration. It also returns calibration data to factory defaults. (
J
page 33,
34)