Panasonic BT-3DL2550 Operating Instructions - Page 34

Performing AUTO CALIBRATION, RESET operation, CALIBRATION, Sub menu, Setting, Description

Get Panasonic BT-3DL2550 PDF manuals and user guides View all Panasonic BT-3DL2550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Main Menu (continued) _ CALIBRATION Select CALIBRATION in the "SYSTEM CONFIG" menu to open the following menus. Sub menu Setting AUTO CALIBRATION *1 RESET *2 Description Connect a CA-210 color analyzer and use this submenu to make a calibration. Select "AUTO CALIBRATION" and select "YES" in the confirmation screen that appears to start calibration. Returns calibration data to their factory defaults. Select "RESET" and select "YES" in the confirmation screen that appears to return calibrated values to their factory defaults. *1 "EXECUTING" is displayed during "AUTO CALIBRATION" and "COMPLETE" appears when calibration ends. "INCOMPLETE" appears if calibration could not be completed. *2 When "RESET" ends, "COMPLETE" appears. Performing AUTO CALIBRATION 1. Press [ , ] in the "SYSTEM CONFIG" menu, select the [CALIBRATION] submenu and press [ENTER]. 2. Press [ , ], select the [AUTO CALIBRATION] submenu and press [ENTER]. RESET operation 1. Press [ , ] in the "SYSTEM CONFIG" menu, select the [CALIBRATION] submenu and press [ENTER]. 2. Press [ , ], select the [RESET] submenu and press [ENTER]. [AUTO CALIBRATION] [RESET] 3. Select "YES" and press [ENTER]. This starts calibration. [AUTO CALIBRATION] 3. Select "YES" and press [ENTER]. This resets the setting of this monitor. [RESET] xxxxxxxx indicates that one of the following messages with the meaning listed below appears. EXECUTING: Operation in progress COMPLETE: Operation completed INCOMPLETE: Operation did not complete. (Check RS-232C cable connection.) xxxxxxxx indicates that the following message with the meaning listed below appears. COMPLETE: Operation completed 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
34
Main Menu
(continued)
_
CALIBRATION
Select CALIBRATION in the “SYSTEM CONFIG” menu to open the following menus.
*1
“EXECUTING” is displayed during “AUTO CALIBRATION” and “COMPLETE” appears when calibration ends.
“INCOMPLETE” appears if calibration could not be completed.
*2
When “RESET” ends, “COMPLETE” appears.
1. Press [
,
] in the “SYSTEM CONFIG” menu,
select the [CALIBRATION] submenu and press
[ENTER].
2. Press [
,
], select the [AUTO CALIBRATION]
submenu and press [ENTER].
3. Select “YES” and press [ENTER].
This starts calibration.
xxxxxxxx indicates that one of the following
messages with the meaning listed below appears.
EXECUTING: Operation in progress
COMPLETE: Operation completed
INCOMPLETE: Operation did not complete.
(Check RS-232C cable connection.)
1. Press [
,
] in the “SYSTEM CONFIG” menu,
select the [CALIBRATION] submenu and press
[ENTER].
2. Press [
,
], select the [RESET] submenu and
press [ENTER].
3. Select “YES” and press [ENTER].
This resets the setting of this monitor.
xxxxxxxx indicates that the following message with
the meaning listed below appears.
COMPLETE: Operation completed
Sub menu
Setting
Description
AUTO CALIBRATION
*1
Connect a CA-210 color analyzer and use this submenu to make a
calibration.
Select “AUTO CALIBRATION” and select “YES” in the
confirmation screen that appears to start calibration.
RESET
*2
Returns calibration data to their factory defaults.
Select “RESET” and select “YES” in the confirmation screen that
appears to return calibrated values to their factory defaults.
Performing AUTO CALIBRATION
[AUTO CALIBRATION]
[AUTO CALIBRATION]
RESET operation
[RE
S
ET]
[RE
S
ET]