Panasonic PT-D4000U Operating Instructions - Page 22

Projection

Get Panasonic PT-D4000U - XGA DLP Projector PDF manuals and user guides
UPC - 791871111529
View all Panasonic PT-D4000U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Projection R/PR G/Y B/PB SYNC/HD VD VIDEO IN S-VIDEO IN REMOTE 1 IN OUT RGB 1 IN REMOTE 2 IN IN SE Powering up the projector When using an optional lens, install a projection lens before powering up the projector. (Refer to page 24.) Remove the lens cover beforehand. Connect the supplied power cord. (120 V AC, 50 Hz/60 Hz) Press the " I " marked side of the MAIN POWER switch to turn on the power. The power indicator lights up red, and the projector is placed in the standby mode. Press the " I " button. [on the main unit or the remote control] The power indicator illuminates in green and soon the image is projected on the screen. Note • If the projector is powered up at about 0 ˚C, a warm-up period of approximately five minutes may be necessary to start projection. The temperature monitor (TEMP) lights during the warm-up period. When the warm-up is completed, the temperature monitor (TEMP) turns off and the image is projected on the screen. • If the surrounding temperature is very low and the warm-up period exceeds five minutes, the control determines it as an abnormal condition and turns off the power automatically. If this happens, raise the surrounding temperature to 0 °C or higher and then turn the main power "on" and turn the power "on" ( | ). Making adjustment and selection It is recommended that the projector be allowed to warm up for at least 30 minutes before any adjustments are made to the focus. Press the FOCUS button to roughly adjust the focus of the lens.* Set the projection scheme in "INSTALLATION" setting. (page 34) Select the input signal by pressing the input selector button to toggle through RGB1, RGB2, VIDEO, S-VIDEO and DVI-D. Turn the feet, and adjust the tilt of the main unit in the front and rear or left and right. Use the lens left/right adjustment dial to adjust the direction of the lens. (page 25) Press the SHIFT button to adjust the "SHIFT".* Press the AUTO SETUP button if the input signal is RGB/DVI signal. (page 25) Press the ZOOM button to fit the image size to the screen size.* Press the FOCUS button again to adjust the "FOCUS".* Press the ZOOM button again to adjust the "ZOOM" and fit the image size to the screen size.* * When operating at the projector, please refer to page 24. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
22
Projection
Powering up the projector
When using an optional lens, install a projection
lens before powering up the projector. (Refer to
page 24.)
Remove the lens cover beforehand.
Connect the supplied power cord.
(120 V AC, 50 Hz/60 Hz)
Press the
“
I
”
marked side of the MAIN
POWER switch to turn on the power.
The power indicator lights up red, and the projector is
placed in the standby mode.
Press the
“
I
”
button. [on the main unit
or the remote control]
The power indicator illuminates in green and soon
the image is projected on the screen.
VD
SYNC/HD
B/P
B
G/Y
R
R/P
SE
REMOTE 1
REMOTE 2 IN
IN
RGB 1 IN
VIDEO IN
S-VIDEO
IN
IN
OUT
Making adjustment and
selection
It is recommended that the projector be allowed to
warm up for at least 30 minutes before any
adjustments are made to the focus.
<Using the remote control>
Press the FOCUS button to roughly
adjust the focus of the lens.*
Set the projection scheme in
“
INSTALLATION
”
setting. (page 34)
Select the input signal by pressing the
input selector button to toggle through
RGB1, RGB2, VIDEO, S-VIDEO and DVI-D.
Turn the feet, and adjust the tilt of the
main unit in the front and rear or left
and right.
Use the lens left/right adjustment dial to
adjust the direction of the lens. (page 25)
Press the SHIFT button to adjust the
“
SHIFT
”
.*
Press the AUTO SETUP button if the
input signal is RGB/DVI signal. (page 25)
Press the ZOOM button to fit the image
size to the screen size.*
Press the FOCUS button again to adjust
the
“
FOCUS
”
.*
Press the ZOOM button again to adjust
the
“
ZOOM
”
and fit the image size to
the screen size.*
* When operating at the projector, please refer to page
24.
•
If the projector is powered up at about 0
˚
C,
a warm-up period of approximately five
minutes may be necessary to start
projection.
The temperature monitor (TEMP) lights
during the warm-up period.
When the warm-up is completed, the
temperature monitor (TEMP) turns off and
the image is projected on the screen.
•
If the surrounding temperature is very low
and the warm-up period exceeds five
minutes, the control determines it as an
abnormal condition and turns off the
power automatically. If this happens, raise
the surrounding temperature to 0
°
C or
higher and then turn the main power
“
on
”
and turn the power
“
on
”
( | ).
Note