ProForm Fusion 6.0 Lx English Manual - Page 17

Locate the High Cable 88.

Get ProForm Fusion 6.0 Lx PDF manuals and user guides View all ProForm Fusion 6.0 Lx manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

38. Wrap the Low Cable (70) over a Pulley (43). 38 Attach the Pulley, a Cable Trap (48), and two Half Finger Guards (46) at the bottom hole of the pair of Pulley Plates (49) with an M10 x 50mm Bolt (106) and an M10 Nylon Locknut (111). Makes sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 39. Attach the Low Cable (70) inside the Right Base 39 (1) with an M10 x 65mm Bolt (110), two M10 Washers (109), and an M10 Nylon Locknut (111). 111 49 46 46 48 106 43 70 111 70 109 40. Locate the High Cable (88). Route the Cable up 40 through the Left Top Frame (4) and over a Pulley (43). Attach the Pulley inside the Top Frame with an M10 x 65mm Bolt (110), two M10 Washers (109), two 1/2" Spacers (68), and an M10 Nylon Locknut (111). 41. Route the High Cable (88) over a Pulley (43) and 41 down through the Left Top Frame (4). Attach the Pulley inside the Top Frame with an M10 x 65mm Bolt (110), two M10 Washers (109), two 1/2" Spacers (68), and an M10 Nylon Locknut (111). 42. Wrap the High Cable (88) under a Pulley (43). 42 Attach the Pulley, a Cable Trap (48), an M10 Washer (109), and two Half Finger Guards (46) to the Small Pulley Plate (50) with an M10 x 50mm Bolt (106) and an M10 Nylon Locknut (111). Makes sure that the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 17 1 109 110 4 43 111 110 68 109 109 68 88 109 68 43 110 109 68 111 88 4 88 46 109 111 46 106 48 43 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
17
38. Wrap the Low Cable (70) over a Pulley (43).
Attach the Pulley, a Cable Trap (48), and two Half
Finger Guards (46) at the bottom hole of the pair
of Pulley Plates (49) with an M10 x 50mm Bolt
(106) and an M10 Nylon Locknut (111).
Makes
sure that the Cable Trap is oriented to hold
the Cable in the groove of the Pulley.
39. Attach the Low Cable (70) inside the Right Base
(1) with an M10 x 65mm Bolt (110), two M10
Washers (109), and an M10 Nylon Locknut (111).
40.
Locate the High Cable (88).
Route the Cable up
through the Left Top Frame (4) and over a Pulley
(43). Attach the Pulley inside the Top Frame with
an M10 x 65mm Bolt (110), two M10 Washers
(109), two 1/2" Spacers (68), and an M10 Nylon
Locknut (111).
41. Route the High Cable (88) over a Pulley (43) and
down through the Left Top Frame (4). Attach the
Pulley inside the Top Frame with an M10 x 65mm
Bolt (110), two M10 Washers (109), two 1/2"
Spacers (68), and an M10 Nylon Locknut (111).
43
46
46
49
106
111
70
48
38
39
1
111
109
70
110
109
41
42
110
40
110
68
43
109
109
111
68
88
4
88
46
46
48
43
50
106
111
109
42. Wrap the High Cable (88) under a Pulley (43).
Attach the Pulley, a Cable Trap (48), an M10
Washer (109), and two Half Finger Guards (46) to
the Small Pulley Plate (50) with an M10 x 50mm
Bolt (106) and an M10 Nylon Locknut (111).
Makes sure that the Cable Trap is oriented to
hold the Cable in the groove of the Pulley.
68
68
43
4
88
109
109
111