Sony LBT-ZX66i Operating Instructions - Page 20

Playing the iPod

Get Sony LBT-ZX66i - iPod Ready Mini Shelf System PDF manuals and user guides
UPC - 027242752481
View all Sony LBT-ZX66i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

To set CD power on Repeat the procedure above and "CD POWER ON" appears in the display. Notes • When "CD POWER OFF" is selected, disc access time is increased. • You cannot change the CD power manage setting in Power Saving Mode (page 27). To change the AM tuning interval The factory setting for AM tuning interval is 10 kHz. Use the buttons on the unit for the operation. 1 Press TUNER/BAND repeatedly to select AM band. 2 Press "/1 to turn off the system. 3 When demonstration appears, hold down TUNING MODE and then press "/1. The system turn on automatically. "AM 9K STEP" or "AM 10K STEP" appears in the display. When you change the interval, all the AM preset stations are erased. Tip To improve broadcast reception, adjust the supplied antennas, or connect an external antenna. To reduce static noise on a weak FM stereo station Press FM MODE repeatedly until "MONO" lights up in the display. There will be no stereo effect, but the reception will improve. 20US Playing the iPod You can listen to audio contents stored in the iPod on this system. 1 Press iPod. 2 Place the iPod. 3 Press NX (or N on the remote) to start playback. 4 Turn VOLUME +/- (or press VOLUME +/- on the remote) to adjust the volume. Notes • When you connect an iPod to the unit, the iPod is automatically turned on if the system is turned on. • When placing or removing the iPod, handle the iPod in the same angle as that of the iPod connector on the unit and do not twist or sway the iPod to prevent connector damage. • Do not carry the unit with an iPod set on the connector. Doing so may cause a malfunction. • When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. • Before disconnecting the iPod, pause playback. • Depending on the connected iPod, you may not able to use m or M while playing video. In this case, you can fast rewind or fast forward by holding down . or >. • To change the volume level, use VOLUME +/-. The volume level does not change even if adjusted on the iPod. • This iPod connector is designed for iPod only. You cannot connect any other portable audio players.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
20
US
To set CD power on
Repeat the procedure above and “CD
POWER ON” appears in the display.
Notes
•
When “CD POWER OFF” is selected, disc
access time is increased.
•
You cannot change the CD power manage
setting in Power Saving Mode (page 27).
To change the AM tuning interval
The factory setting for AM tuning interval
is 10 kHz.
Use the buttons on the unit for the
operation.
1
Press TUNER/BAND repeatedly to
select AM band.
2
Press
"/1
to turn off the system.
3
When demonstration appears, hold
down TUNING MODE and then
press
"/1
.
The system turn on automatically.
“AM 9K STEP” or “AM 10K STEP”
appears in the display.
When you change the interval, all the AM
preset stations are erased.
Tip
To improve broadcast reception, adjust the
supplied antennas, or connect an external
antenna.
To reduce static noise on a weak FM
stereo station
Press FM MODE repeatedly until
“MONO” lights up in the display.
There will be no stereo effect, but the
reception will improve.
Playing the iPod
You can listen to audio contents stored in
the iPod on this system.
1
Press iPod.
2
Place the iPod.
3
Press
NX
(or
N
on the
remote) to start playback.
4
Turn VOLUME +/– (or press
VOLUME +/– on the remote) to
adjust the volume.
Notes
•
When you connect an iPod to the unit, the
iPod is automatically turned on if the system
is turned on.
•
When placing or removing the iPod, handle
the iPod in the same angle as that of the iPod
connector on the unit and do not twist or sway
the iPod to prevent connector damage.
•
Do not carry the unit with an iPod set on the
connector. Doing so may cause a malfunction.
•
When placing or removing the iPod, brace the
unit with one hand and take care not to press
the controls of the iPod by mistake.
•
Before disconnecting the iPod, pause
playback.
•
Depending on the connected iPod, you may
not able to use
m
or
M
while playing
video. In this case, you can fast rewind or fast
forward by holding down
.
or
>
.
•
To change the volume level, use
VOLUME +/–. The volume level does not
change even if adjusted on the iPod.
•
This iPod connector is designed for iPod only.
You cannot connect any other portable audio
players.