Sony SLT-A35K Instruction Manual (Large File - 12.9 MB) - Page 37

Select [Cleaning Mode] with, control button.

Get Sony SLT-A35K PDF manuals and user guides View all Sony SLT-A35K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Preparing the camera Cleaning the image sensor If dust or debris enters the camera and adheres to the image sensor (the part that acts as the film), it may appear as dark spots on the photo image, depending on the shooting environment. If there is dust on the image sensor, clean the image sensor following the steps below. Notes • Cleaning cannot be performed when the battery level is 50% or less. • The camera starts beeping if the battery pack becomes low during cleaning. Stop cleaning immediately and turn the camera off. The use of an AC-PW20 AC Adaptor (sold separately) is recommended. • The cleaning should be completed quickly. • Do not use a spray blower because it may scatter water droplets inside the camera body. To clean the image sensor automatically using the cleaning mode of the camera 1 Confirm that the battery is fully charged (page 23). 2 Press the MENU button, then select 2 with b/B on the control button. MENU button 3 Select [Cleaning Mode] with v/V, then press the center of the control button. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
37
Preparing the camera
If dust or debris enters the camera and adheres to the image sensor (the part
that acts as the film), it may appear as dark spots on the photo image,
depending on the shooting environment. If there is dust on the image
sensor, clean the image sensor following the steps below.
Notes
• Cleaning cannot be performed when the battery level is 50% or less.
• The camera starts beeping if the battery pack becomes low during cleaning. Stop
cleaning immediately and turn the camera off. The use of an AC-PW20 AC Adaptor
(sold separately) is recommended.
• The cleaning should be completed quickly.
• Do not use a spray blower because it may scatter water droplets inside the camera
body.
To clean the image sensor automatically using the cleaning mode of the
camera
Cleaning the image sensor
1
Confirm that the battery is fully charged (page 23).
2
Press the MENU button, then
select
2 with
b
/
B
on the
control button.
MENU button
3
Select [Cleaning Mode] with
v
/
V
,
then press the center of the
control button.