Sony STR DA2400ES Service Manual - Page 86
Digital Video Board, Ic3000, M30620fcpgp U5c Hdmi Controller
UPC - 027242729872
View all Sony STR DA2400ES manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 86 highlights
STR-DA2400ES/DG920 • IC Pin Function Description DIGITAL VIDEO BOARD IC3000 M30620FCPGP U5C (HDMI CONTROLLER) Pin No. 1 to 5 6 Pin Name I/O NC O BYTE I 7 CNVSS I 8, 9 NC O 10 RESET I 11 XOUT O 12 VSS - 13 XIN I 14 VCC_3.3V - 15 NMI I 16 to 18 NC O 19 RX_RST O 20 RX_INT I 21 1444_HPD O 22 HPD_IN1 O 23 to 26 NC O 27 CSCL O 28 CSDA I/O 29 232COUT (VU TX) O 30 232CIN (VU RX) I 31 CLK 1 I 32 RTS 1 O 33 VUCOM_SDA I/O 34 VUCOM_SCL I 35, 36 EDID_SELA, EDID_SELB O 37 to 39 NC O 40 VDAC_RESET O 41 TX_5VPWR O 42 TX_RST O 43 TX_INT I 44 to 50 NC O 51 to 53 1444_SELA to 1444_SELC O 54 1444_OEB O 55, 56 P5V_SELA, P5V_SELB O 57 to 59 NC O 60 VCC_3.3V - 61 NC O 62 VSS - 63 NC O 64 NON LPCM O 65 MUTE O 66 to 90 NC O 91 to 93 MODEL_SW3 to MODEL_SW1 I 94 AVSS - 95 NC O 96 VREF I 97 AVCC - 98 to 100 NC O Description Not used External data bus width selection signal input terminal "L": 16 bit Fixed at "L" in this set Processor mode selection signal input terminal "L": single chip mode Fixed at "L" in this set Not used Reset signal input from the system controller "L": reset System clock output terminal (10 MHz) Ground terminal System clock input terminal (10 MHz) Power supply terminal (+3.3V) Non-maskable interrupt signal input terminal Not used Not used Reset signal output to the HDMI receiver "L": reset Interrupt signal input from the HDMI receiver Hot plug detection control signal output to the HDMI input selector Hot plug detection control signal output to the HDMI VIDEO 1 IN connector Not used I2C clock signal output to the EEPROM, HDMI receiver and HDMI transceiver I2C data bus with the EEPROM, HDMI receiver and HDMI transceiver Serial data output terminal for RS-232C Serial data input terminal for RS-232C Not used Not used I2C data bus with the system controller I2C clock signal input from the system controller Input data selection signal output terminal Not used Not used Power supply on/off control signal output terminal for HDM IOUT connector Reset signal output to the HDMI transceiver "L": reset Interrupt signal input from the HDMI transceiver Not used "H": power on HDMI input selection signal output to the HDMI input selector Output enable signal output to the HDMI input selector HDMI +5V power input selection signal output terminal Not used Power supply terminal (+3.3V) Not used Ground terminal Not used Non-LPCM setting signal output terminal "L": LPCM System muting signal output terminal Not used Model setting terminal Ground terminal Not used Reference voltage (+3.3V) input terminal Power supply terminal (+3.3V) Not used 86