Sony VPL-HW20 Operating Instructions - Page 64

Message Lists, Message, Cause and Remedy

Get Sony VPL-HW20 PDF manuals and user guides View all Sony VPL-HW20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Message Lists Warning messages Message Cause and Remedy High temp.! Lamp off in 1 min. c Turn off the power. c Check to ensure that nothing is blocking the ventilation holes. (1 page 12) Frequency is out of range! c Frequency is out of range. Input a signal that is within the acceptable frequency range of the projector. (1 page 72) Please check Input-A Signal Sel. c Set "Input-A Signal Sel." in the Setup menu to "Computer" when an RGB signal is input from a computer. (1 page 51) Please replace the Lamp/ Filter. c It is time to replace the lamp. Replace the lamp. (1 page 65) c Also, replace the air filter too. Restart cleaning the ventilation holes (intake). (1 page 65) If this message appears again after you replace the lamp and filter, the lamp replacement process is not complete. Check the lamp replacement process. (1 page 65) Note To clear this message, press any button either on the remote control or the control panel of the projector once. Please clean the filter. c It is time to clean the air filter. Clean the air filter. (1 page 68) Note To clear this message, press any button either on the remote control or the control panel of the projector once. Please clean the filter. Have you finished? Yes No c It is time to clean the air filter. Clean the air filter. (1 page 68) c If you cleaned the air filter, select "Yes." If you did not clean the air filter, select "No." Projector temperature is high. Cooling Setting should be "High" if projector is being used at high altitude. c Check to ensure that the ventilation holes on the unit are not covered. (1 page 12) c When using the projector at high altitude, set the Cooling Setting to "High". (1 page 50) Note When temperature inside the projector remains high, the Cooling Setting is switched to "High" in 1 minute, then the fan speed increases. Caution messages Message x Not applicable! 64 Cause and Remedy c No signal is input in the selected input. Check connections. (1 page 22) c Press the appropriate button. c The operation to be activated by the button is currently prohibited.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
64
Warning messages
Caution messages
Message Lists
Message
Cause and Remedy
High temp.! Lamp off in 1
min.
c
Turn off the power.
c
Check to ensure that nothing is blocking the ventilation holes.
(
1
page 12)
Frequency is out of range!
c
Frequency is out of range. Input a signal that is within the
acceptable frequency range of the projector. (
1
page 72)
Please check Input-A
Signal Sel.
c
Set “Input-A Signal Sel.” in the Setup
menu to
“Computer” when an RGB signal is input from a computer.
(
1
page 51)
Please replace the Lamp/
Filter.
c
It is time to replace the lamp. Replace the lamp. (
1
page 65)
c
Also, replace the air filter too. Restart cleaning the ventilation
holes (intake). (
1
page 65)
If this message appears again after you replace the lamp and
filter, the lamp replacement process is not complete. Check the
lamp replacement process. (
1
page 65)
To clear this message, press any button either on the remote control
or the control panel of the projector once.
Please clean the filter.
c
It is time to clean the air filter. Clean the air filter. (
1
page 68)
To clear this message, press any button either on the remote control
or the control panel of the projector once.
Please clean the filter. Have
you finished? Yes No
c
It is time to clean the air filter. Clean the air filter. (
1
page 68)
c
If you cleaned the air filter, select “Yes.” If you did not clean the
air filter, select “No.”
Projector temperature is
high. Cooling Setting
should be “High” if
projector is being used at
high altitude.
c
Check to ensure that the ventilation holes on the unit are not
covered. (
1
page 12)
c
When using the projector at high altitude, set the Cooling
Setting to “High”. (
1
page 50)
When temperature inside the projector remains high, the Cooling
Setting is switched to “High” in 1 minute, then the fan speed
increases.
Message
Cause and Remedy
c
No signal is input in the selected input. Check connections.
(
1
page 22)
Not applicable!
c
Press the appropriate button.
c
The operation to be activated by the button is currently
prohibited.
Note
Note
Note
x