TEAC 2488neo 2488neo Owner's Manual - Page 34

Stereo dynamics, Stereo fader, The STEREO DYNAMICS screen appears.

Get TEAC 2488neo PDF manuals and user guides View all TEAC 2488neo manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

5 − Mixer Stereo dynamics The stereo bus has a stereo dynamics processor (compressor or expander) available. 1 With the SHIFT indicator lit, press the SELECT key. The STEREO DYNAMICS screen appears. 2 Press the YES/ENTER key. The DYNAMICS LIBRARY screen appears. 3 Use the Ó/Á cursor keys to select preset setting (PRESET) or the user setting (USER). The PRESET category contains factory preset settings, while USER can be used to save and recall custom settings. 4 Use the dial to select library entries 5 Press YES/ENTER to load the entry. The STEREO DYNAMICS screen reappears, and the selected preset parameters appear. 6 Use the cursor keys and dial to select and adjust the parameters for the effect. Note that the last parameter is an on/off switch. When set to off, the dynamics processor is bypassed. NOTE The stereo dynamics and mastering compressor (see page 71) are not compatible. Stereo fader Press the STEREO key to open the screen below. As with the channel fader screen, the on-screen fader cannot be used to make adjustments. Also note that the internal fader value and the top panel physical fader position may not correspond (see "Faders" on page 32). In this case, the LVL value corresponds to the physical fader level, and INT gives the internal virtual fader value (as marked by the triangular symbol beside the on-screen fader). In both cases, 0 is full cut, 127 is full up, and 100 is the unity gain value. 34 TASCAM 2488neo

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
34
TASCAM
2488neo
5 − Mixer
Press the
STEREO
key to open the screen below.
As with the channel fader screen, the on-screen fader can-
not be used to make adjustments. Also note that the inter-
nal fader value and the top panel physical fader position
may not correspond (see
“
Faders
”
on page 32).
In this case, the
LVL
value corresponds to the physical fader
level, and
INT
gives the internal virtual fader value (as
marked by the triangular symbol beside the on-screen fader).
In both cases, 0 is full cut, 127 is full up, and 100 is the
unity gain value.
Stereo fader
The stereo bus has a stereo dynamics processor (compres-
sor or expander) available.
1
With the
SHIFT
indicator lit, press the
SELECT
key.
The STEREO DYNAMICS screen appears.
2
Press the
YES/ENTER
key. The DYNAMICS
LIBRARY screen appears.
3
Use the
Ó
/
Á
cursor keys to select preset setting
(
PRESET
) or the user setting (
USER
).
The
PRESET
category contains factory preset
settings, while
USER
can be used to save and recall
custom settings.
4
Use the dial to select library entries
5
Press
YES/ENTER
to load the entry.
The STEREO DYNAMICS screen reappears, and
the selected preset parameters appear.
6
Use the cursor keys and dial to select and adjust the
parameters for the effect. Note that the last param-
eter is an on/off switch. When set to off, the dynam-
ics processor is bypassed.
NOTE
The stereo dynamics and mastering compressor (see
page 71) are not compatible.
Stereo dynamics