Thermador VCIN36JP Installation Instructions - Page 11

Assembly of the Transition

Get Thermador VCIN36JP PDF manuals and user guides View all Thermador VCIN36JP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Assembly of the Transition 10" (254 mm) Duct 10¼" (260 mm) 1" (25.4 mm) screw x2 1213/16" (325 mm) 3 5/16" (84 mm) 17½" (445 mm) Figure 2: Transition Dimensions 4 5/16" (502 mm) 21¾" (552 mm) 11¼" (286 mm) 17½" (444 mm) Figure 4: Transition Centerline 1. A minimum height clearance of 10¼" (260 mm) is needed above the hood for transition mounting. 2. Remove transition from inside of hood. Discard brackets attaching transition to the inside of hood. 3. Align mounting holes at base of transition with the mounting holes of the 1/2" (13 mm) flange located at the top or rear of the hood. 4. Fasten transition to hood using two (2) 1" (25.4 mm) sheet metal screws included with hood. 5. Seal connection between transition and hood with aluminum tape. DO NOT use duct tape. 6. Remove tape holding damper closed. Figure 3: Transition Cutout English 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
English 9
Assembly of the Transition
1.
A minimum height clearance of 10¼” (260 mm) is
needed above the hood for transition mounting.
2.
Remove transition from inside of hood. Discard
brackets attaching transition to the inside of hood.
3.
Align mounting holes at base of transition with the
mounting holes of the 1/2” (13 mm) flange located at
the top or rear of the hood.
4.
Fasten transition to hood using two (2) 1” (25.4 mm)
sheet metal screws included with hood.
5.
Seal connection between transition and hood with
aluminum tape. DO NOT use duct tape.
6.
Remove tape holding damper closed.
Figure 2: Transition Dimensions
Figure 3: Transition Cutout
10” (254 mm)
Duct
17½” (445 mm)
3
5
16
(84 mm)
/
”
1” (25.4 mm)
screw x2
21¾”
(552 mm)
11¼”
(286 mm)
4
5/
16
"
(502 mm)
17½”
(444 mm)
Figure 4: Transition Centerline
10¼”
(260 mm)
12
13
/
16
”
(325 mm)