Toshiba 26HF66 User Manual - Page 16

Programming the remote control to operate, your other devices

Get Toshiba 26HF66 PDF manuals and user guides View all Toshiba 26HF66 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

To control a DVD player: Program the remote control to recognize the brand of your DVD player (see "Programming the remote control to operate your other devices" below). The buttons shown at right will then control the DVD player. Press "DVD" first. Power Input (TV) Recall Mute (TV) Number buttons Volume +/- (TV) DVD Pic Size (TV) DVD MENU ▲▼ ENTER DVD controls ▼ DVD Skip/Search / TOP Menu DVD Clear Using the Remote Control ▼ Programming the remote control to operate your other devices This remote control is pre-programmed to operate most Toshiba satellite receivers, VCRs, and DVD players. To control a non-Toshiba device (or a Toshiba device that the remote control is not preprogrammed to operate), you must follow the steps below to program your remote control. 1. Refer to the device code tables (on pages 17 and 18) to find the corresponding code for your device. If more than one code is listed, try each one separately until you find the one that works. 2. If you are programming the remote control to operate your: • Cable TV converter/satellite receiver: Press "CBL/SAT." • VCR: Press "VCR." • DVD player: Press "DVD." 3. While holding down RECALL, press the Channel Number buttons to enter the three-digit code for your device within 10 seconds. Note: If you do not enter the code within 10 seconds from step 3, or if you enter the wrong code, this operation is canceled. 4. Point the remote control at the device and press POWER to test the code. • If the device responds, you entered the correct code. • If the device does not respond, repeat steps 1-4 using another code. 5. Press "TV" to control the TV. For future reference, write down the codes you used: Cable TV converter/satellite receiver code VCR code DVD player code Power Recall Channel Numbers TV VCR DVD CBL/SAT Note: • When shipped from the factory, the remote control is set to operate your TV. • Each time you replace the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled "VCR1/VCR2." If your VCR has this kind of switch and does not respond to any of the codes for your VCR, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control. 16 J3W60321A_En_p15-22 16 27/2/06, 9:54 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
16
Using the
Remote Control
Programming the remote control to operate
your other devices
This remote control is pre-programmed to operate most Toshiba
satellite receivers, VCRs, and DVD players. To control a non-Toshiba
device (or a Toshiba device that the remote control is not pre-
programmed to operate), you must follow the steps below to program
your remote control.
1.
Refer to the device code tables (on pages 17 and 18) to find the
corresponding code for your device.
If more than one code is listed, try each one separately until you
find the one that works.
2.
If you are programming the remote control to operate your:
•Cable TV converter/satellite receiver: Press “CBL/SAT.”
• VCR: Press “VCR.”
• DVD player: Press “DVD.”
3.
While holding down RECALL, press the Channel Number buttons
to enter the three-digit code for your device within 10 seconds.
Note:
If you do not enter the code within 10 seconds from step 3,
or if you enter the wrong code, this operation is canceled.
4.
Point the remote control at the device and press POWER to test
the code.
• If the device responds, you entered the correct code.
• If the device does not respond, repeat steps 1–4 using another
code.
5.
Press “TV” to control the TV.
For future reference, write down the codes you used:
Cable TV converter/satellite receiver code _____________________
VCR code
______________________________________________
DVD player code _________________________________________
Note:
•
When shipped from the factory, the remote
control is set to operate your TV.
•
Each time you replace the batteries, you
must reprogram the remote control.
•
Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and
does not respond to any of the codes for
your VCR, set the switch to the other
position (VCR1 or VCR2) and reprogram
the remote control.
Recall
Channel
Numbers
Program the remote
control to recognize the
brand of your DVD
player (see
“Program
ming the
remote control
to
operate your other
devices” below). The
buttons shown at right
will then control the
DVD player.
Press “DVD” first.
Power
Number
buttons
DVD Skip/Search
/
DVD
Recall
TOP Menu
ENTER
DVD MENU
Pic Size (TV)
Mute (TV)
Input (TV)
Volume +/–
(TV)
DVD controls
To control a DVD player:
▲▼
▼
▼
DVD Clear
TV
VCR
DVD
CBL/SAT
Power
J3W60321A_En_p15-22
27/2/06, 9:54 AM
16