ViewSonic PJD6683ws PJD5126, PJD6223, PJD6253, PJD6553W, PJD5226, PJD5226W, PJ - Page 27

Operation

Get ViewSonic PJD6683ws PDF manuals and user guides View all ViewSonic PJD6683ws manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector flashes blue after power has been applied. 2. Press II POWER on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness. • If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. • To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off. 3. If the projector is activated for the first time, select your OSD language following the on-screen instructions. 4. Switch all of the connected equipment on. 5. The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed until an input signal is found. You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 27 for details. If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 67 for details. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
22
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted). Check that the
POWER
indicator light
on the projector flashes blue
after power has been applied.
2.
Press
POWER
on the projector or remote
control to start the projector. The
POWER
indicator light
stays blue when the projector is
on.
(If necessary) Rotate the focus ring to adjust the image clearness.
•
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 90 seconds before energizing the lamp.
•
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
3.
If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
4.
Switch all of the connected equipment on.
5.
The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message '
No Signal
' will continue to be displayed until an input
signal is found.
You can also press
SOURCE
on the projector or remote control to select your desired
input signal. See
"Switching input signal" on page 27
for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See
"Timing chart" on page 67
for details.
I
I