ViewSonic PJD6683ws PJD5126, PJD6223, PJD6253, PJD6553W, PJD5226, PJD5226W, PJ - Page 50

Using the projector in standby mode, Shutting down the projector

Get ViewSonic PJD6683ws PDF manuals and user guides View all ViewSonic PJD6683ws manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

PJLink™, SNMP, AMX and Xpanel formats supported This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, please follow its user guide or website respectively to control and manage projectors. Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure you have turned on the corresponding menus under SYSTEM SETUP: Basic > Standby Settings, and the cable connections are correctly made. For the connection methods, see the Connection chapter. Power Saving Less than 1W power consumption when Power Saving mode is turned on. • When Power Saving is On, the following settings are not available. • When Power Saving is On, the network function is not available when the projector is in standby mode. Active VGA Out Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT sockets are correctly connected to devices. The projector outputs the signal received only from COMPUTER IN 1. Active Audio Out Selecting On outputs an audio signal when the AUDIO IN 1 and AUDIO OUT sockets are correctly connected to devices. The projector outputs the audio signal received only from AUDIO IN 1. Quick Power Off Selecting On enables the function and the projector will not enter the cooling process after being shut down. Selecting Off disables the function and the projector will enter normal cooling process after being shut down. • If you attempt to restart the projector right after it's been turned off, it may not be turned on successfully and will rerun its cooling procedure. • When Off is selected, the Smart Restart function will be automatically turned off. Shutting down the projector 1. Press II POWER and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. Press II POWER a second time. 3. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. CAUTION • To protect the lamp, the projector will not respond to any commands during the cooling process. • To shorten the cooling time, you can also activate the Quick Power Off function. See "Quick Power Off" on page 45 for details. • Do not unplug the power cord before the projector shutdown sequence is complete. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
45
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details,
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
SYSTEM SETUP: Basic
>
Standby Settings
, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 1W power consumption when
Power Saving
mode is turned on.
•
When Power Saving is On, the following settings are not available.
•
When Power Saving is On, the network function is not available when the projector is in
standby mode.
Active VGA Out
Selecting
On
outputs a VGA signal when the
COMPUTER IN 1
and
COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only
from
COMPUTER IN 1
.
Active Audio Out
Selecting
On
outputs an audio signal when the
AUDIO IN 1
and
AUDIO OUT
sockets are
correctly connected to devices. The projector outputs the audio signal received only from
AUDIO IN 1
.
Quick Power Off
Selecting
On
enables the function and the projector will not enter the cooling process after
being shut down. Selecting
Off
disables the function and the projector will enter normal
cooling process after being shut down.
•
If you attempt to restart the projector right after it’s been turned off, it may not be turned
on successfully and will rerun its cooling procedure.
•
When Off is selected, the Smart Restart function will be automatically turned off.
Shutting down the projector
1.
Press
POWER
and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
Press
POWER
a second time.
3.
Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
•
To protect the lamp, the projector will not respond to any commands during the cooling
process.
•
To shorten the cooling time, you can also activate the Quick Power Off function. See
"Quick Power Off" on page 45
for details.
•
Do not unplug the power cord before the projector shutdown sequence is complete.
I
I
I
I