Weider Pro 9645 English Manual - Page 9

identification

Get Weider Pro 9645 PDF manuals and user guides View all Weider Pro 9645 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

12. Press a 1" Round Inner Cap (49) into one of 12 the Press Arms (46). Press a 1 3/4" Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16" x 2 1/2" Bolts (22) and two 5/16" Nylon Locknuts (3). 22 Assemble the other Press Arm (46) in the 8 same manner. 46 49 -46 17 13. Identify the Right Arm (48) and the Left Arm (47). Note the position of the welded bracket 13 on each Arm. Arm identification is very 86 31-9 31 ,g9r cn important for step 14. 50 - --4 3 Welded 47 Attach a "V"-Pulley (50) and a Long Cable Brackets Trap (31) to the Right Arm (48) with a 3/8" x 2 1/2" Bolt (86) and a 3/8" Nylon Locknut (21). 4-__\ 21 Do not tighten the Nylon Locknut yet. Attach a "V"-Pulley (50) and a Long Cable Trap (31) to the Left Arm (47) in the same 48 manner. (i ) 14. Lubricate both axles on the Top Frame (55). 14 Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 13 to identify the Right Arm. Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55). Tap two 1" Retainers (69) and a 1" Round Cover Cap (70) onto the axle. Be sure that 48 the teeth on the Retainers bend toward the Round Cover Cap, as shown in the inset drawing. Attach the Left Arm (47) in the same manner. Press 1 3/4" Square Inner Caps (44) into the lower ends of the Right and Left Arms (47, 48). Wet the lower end of each Arm with soapy water. Slide a 10" Pad (45) onto the lower end of each Arm. 44 45 55 Bracket 47 Lubricate Axle 69 45 70 44 Axle 69 70 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
12.
Press
a
1"
Round
Inner
Cap
(49)
into
one
of
the
Press
Arms
(46).
Press
a
1
3/4"
Square
Inner
Cap
(44)
into
the
Press
Arm.
Attach
the
Press
Arm
(46)
to
one
side
of
the
Press
Frame
(17)
with
two
5/16"
x
2
1/2"
Bolts
(22)
and
two
5/16"
Nylon
Locknuts
(3).
Assemble
the
other
Press
Arm
(46)
in
the
same
manner.
13.
Identify
the
Right
Arm
(48)
and
the
Left
Arm
(47).
Note
the
position
of
the
welded
bracket
on
each
Arm.
Arm
identification
is
very
important
for
step
14.
Attach
a
"V"
-Pulley
(50)
and
a
Long
Cable
Trap
(31)
to
the
Right
Arm
(48)
with
a
3/8"
x
2
1/2"
Bolt
(86)
and
a
3/8"
Nylon
Locknut
(21).
Do
not
tighten
the
Nylon
Locknut
yet.
Attach
a
"V"
-Pulley
(50)
and
a
Long
Cable
Trap
(31)
to
the
Left
Arm (47)
in
the
same
manner.
(
i
)
14.
Lubricate
both
axles
on
the
Top
Frame
(55).
Slide
the
Right
Arm
(48)
onto
the
right
axle.
Note:
Be
careful
not
to
confuse
the
Right
Arm
with
the
Left
Arm
(47);
refer
to
step
13
to
identify
the
Right
Arm.
Be
sure
that
the
upper
end
of
the
Right
Arm
is
behind
the
indicated
bracket
on
the
Top
Frame
(55).
Tap
two
1"
Retainers
(69)
and
a
1"
Round
Cover
Cap
(70)
onto
the
axle.
Be
sure
that
the
teeth
on
the
Retainers
bend
toward
the
Round
Cover
Cap,
as
shown
in
the
inset
drawing.
Attach
the
Left
Arm
(47)
in
the
same
manner.
Press
1
3/4"
Square
Inner
Caps
(44)
into
the
lower
ends
of
the
Right
and
Left
Arms
(47,
48).
Wet
the
lower
end
of
each
Arm
with
soapy
water.
Slide
a
10"
Pad
(45)
onto
the
lower
end
of
each
Arm.
12
8
46
22
17
49
—46
13
86
31
,
g9r
cn
31-9
50
-
--
4
3
Welded
Brackets
4-__\
21
48
47
14
48
44
45
55
Bracket
Lubricate
Axle
69
70
Axle
47
45
44
69
70
9