Yamaha CVP-509 Owner's Manual - Page 111

CVP-509/505: Keyboard Stand Assembly

Get Yamaha CVP-509 PDF manuals and user guides View all Yamaha CVP-509 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

3 CVP-509/505: Keyboard Stand Assembly CAUTION • Assemble the stand on a flat floor with ample space. • Be careful not to confuse parts, and be sure to install all parts in the correct direc- tion. Please assemble in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. • Be sure to tighten up all screws upon completing assembly of each unit. • To disassemble, reverse the assembly sequence given below. Have a Phillips-head (+) screwdriver of the appropriate size ready. 2 With the key cover closed, lean A against the wall. 1 Spread a large soft cloth, such as a blanket on the floor in front of the wall. 2 Place A on the cloth with the keyboard side turned to the wall. CAUTION • Be careful not to pinch your fingers. • Do not lay the main unit upside-down on the floor. Place the protection pads under the keyboard. 10cm 10cm 1 Remove all parts from the box. Confirm that all parts shown in the illustration are provided. Main unit A CAUTION To prevent the key cover from accidentally opening during assembly, press down on the key cover, making sure that the sheet (shown) remains in place. Front leg (left) B Rear leg D Front leg (right) C 3 Raise A from the backside, and lean A against the wall with the keyboard side on the bottom. CAUTION • The top part of the music rest is not fixed. Support the music rest with your hand so that the music rest will not fall. • Do not place the main unit with the rear side facing down. Large soft cloth E Pedal box metal Pedal box F Rear legs metal cover G Bundled pedal cord inside AC power cord Assembly Parts 4 x 10 mm screws for the cover x 2 5 x 30 mm long screws x 4 Washers x 4 5 x 18 mm short screws x 10 4 x 20 mm thin screws x 3 Protective pads x 2 Protective pads CAUTION Please do not touch the speaker net. Doing so may damage the speaker inside. CVP-509/505: Keyboard Stand Assembly CVP-509/505/503/501 Owner's Manual 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
CVP-509/505: Keyboard Stand Assembly
CVP-509/505/503/501 Owner’s Manual
111
3
CVP-509/505: Keyboard Stand
Assembly
CAUTION
• Assemble the stand on a flat floor with ample space.
• Be careful not to confuse parts, and be sure to install all parts in the correct direc-
tion. Please assemble in accordance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below. Use of incorrect screws
can cause damage.
• Be sure to tighten up all screws upon completing assembly of each unit.
• To disassemble, reverse the assembly sequence given below.
1
Remove all parts from the box. Confirm that all
parts shown in the illustration are provided.
2
With the key cover closed, lean A against the
wall.
1
Spread a large soft cloth, such as a blanket on the floor in front of
the wall.
2
Place A on the cloth with the keyboard side turned to the wall.
3
Raise A from the backside, and lean A against the wall with the
keyboard side on the bottom.
Have a Phillips-head (+) screwdriver of the appropriate size ready.
B
C
E
G
F
A
D
Main unit
Front leg (left)
Front leg (right)
Rear leg
Pedal box metal
Pedal box
Bundled pedal cord
inside
Rear legs metal cover
AC power cord
4 x 10 mm screws for the cover x 2
5 x 30 mm long screws x 4
5 x 18 mm short screws x 10
Washers x 4
CAUTION
To prevent the key cover from accidentally opening during
assembly, press down on the key cover, making sure that the
sheet (shown) remains
in place.
Assembly Parts
4 x 20 mm thin screws x 3
Protective pads x 2
CAUTION
• Be careful not to pinch your fingers.
• Do not lay the main unit upside-down on the floor.
Place the protection pads under the keyboard.
10cm
10cm
Large soft cloth
CAUTION
• The top part of the music rest is not fixed. Support the music rest
with your hand so that the music rest will not fall.
• Do not place the main unit with the rear side facing down.
Protective pads
CAUTION
Please do not touch the speaker net. Doing so may damage the
speaker inside.