Yamaha RX-V363 Owner's Manual - Page 16

Setting the speaker impedance (U.S.A. and Canada models only), Connecting to the FRONT A terminals - setup

Get Yamaha RX-V363 - AV Receiver PDF manuals and user guides
UPC - 027108929781
View all Yamaha RX-V363 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Connections ■ Connecting to the FRONT A terminals 2 1 Red: positive (+) Black: negative (-) 3 Setting the speaker impedance (U.S.A. and Canada models only) Caution If you are to use 6 ohm speakers, set "SP IMP." to "6ΩMIN" as follows BEFORE using this unit. 1 Loosen the knob. 2 Insert the bare end of the speaker wire into the slit on the terminal. 3 Tighten the knob to secure the wire. Connecting the banana plug (except Europe, Russia, Korea, and Asia models) The banana plug is a single-pole electrical connector widely used to terminate speaker cables. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal. 1 Make sure this unit is turned off. See page 19 for details about turning on or off this unit. 2 Press and hold JTONE CONTROL and then press ASTANDBY/ON to turn on this unit. This unit turns on, an the advanced setup menu appears in the front panel display. 3 Press KPROGRAM l / h repeatedly to select "SP IMP.". The following display appears in the front panel display. Banana plug SP IMP.- 8 MIN ■ Connecting to the FRONT B, CENTER, and SURROUND terminals 4 Press LSTRAIGHT repeatedly to select "6ΩMIN". The following display appears in the front panel display. Red: positive (+) Black: negative (-) 1 Press down the tab. 2 Insert the bare end of the speaker wire into the hole on the terminal. 3 Release the tab to secure the wire. SP IMP.- 6 MIN 5 Press ASTANDBY/ON to confirm your selection and set this unit to the standby mode. Note The setting you made is reflected next time you turn on this unit. 12 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
12
En
Connections
■
Connecting to the FRONT A terminals
1
Loosen the knob.
2
Insert the bare end of the speaker wire into
the slit on the terminal.
3
Tighten the knob to secure the wire.
Connecting the banana plug
(except Europe, Russia, Korea, and Asia models)
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables. First, tighten the
knob and then insert the banana plug connector into the
end of the corresponding terminal.
■
Connecting to the FRONT B, CENTER,
and SURROUND terminals
1
Press down the tab.
2
Insert the bare end of the speaker wire into
the hole on the terminal.
3
Release the tab to secure the wire.
1
Make sure this unit is turned off.
See page 19 for details about turning on or off this
unit.
2
Press and hold
J
TONE CONTROL
and
then press
A
STANDBY/ON
to turn on this
unit.
This unit turns on, an the advanced setup menu
appears in the front panel display.
3
Press
K
PROGRAM
l
/
h
repeatedly to
select “SP IMP.”.
The following display appears in the front panel
display.
4
Press
L
STRAIGHT
repeatedly to select
“6
Ω
MIN”.
The following display appears in the front panel
display.
5
Press
A
STANDBY/ON
to confirm your
selection and set this unit to the standby
mode.
The setting you made is reflected next time you turn on this unit.
1
2
3
Red: positive (+)
Black: negative (–)
Banana plug
Red: positive (+)
Black: negative (–)
Setting the speaker impedance
(U.S.A. and Canada models only)
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to
“6
Ω
MIN” as follows BEFORE using this unit.
Note
SP IMP.- 8 MIN
SP IMP.- 6 MIN