Yamaha RX-V363 Owner's Manual - Page 23

Connecting the FM and AM antennas, Connecting the power cable, Turning on and off the power - model

Get Yamaha RX-V363 - AV Receiver PDF manuals and user guides
UPC - 027108929781
View all Yamaha RX-V363 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

PREPARATION Connecting the FM and AM antennas Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals. Notes • The AM loop antenna should be placed away from this unit. • A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center about outdoor antennas. • The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit. Outdoor AM antenna Use a 5 to 10 m (16 to 32 ft) of vinyl-covered wire extended outdoors from a window. AM loop antenna (supplied) Connections Assembling the supplied AM loop antenna Note The types of the supplied AM loop antenna is different depending on the models. Connecting the power cable Once all connections are complete, plug the power cable into the AC wall outlet. ANTENNA DEO N DVR OUT MONITOR OUT AM GND Indoor FM antenna (supplied) FM 75 UNBAL. R SURRO AUDIO N DVR OUT CD IN MD/ OUT (PLAY) CD-R (REC) OUTP S Ground For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. Power cable (U.S.A. model) To the AC wall outlet Turning on and off the power ■ Turning on this unit Connecting the wire of the AM loop antenna Open the lever Insert Close the lever Press ASTANDBY/ON (or D POWER) to turn on this unit. y When you turn on this unit, there will be a 4 to 5-second delay before this unit can reproduce sound. ■ Set this unit to the standby mode y The wire of the AM loop antenna does not have any polarity and you can connect either end of the wire to AM or GND terminal. Press ASTANDBY/ON (or E STANDBY) to set this unit to the standby mode. Note In the standby mode, this unit consumes a small amount of power in order to receive infrared signals from the remote control. English 19 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
19
En
Connections
PREPARATION
English
Both FM and AM indoor antennas are supplied with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
•
The AM loop antenna should be placed away from this unit.
•
A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.
•
The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
Connecting the wire of the AM loop antenna
y
The wire of the AM loop antenna does not have any polarity
and you can connect either end of the wire to AM or GND
terminal.
Assembling the supplied AM loop antenna
The types of the supplied AM loop antenna is different
depending on the models.
Once all connections are complete, plug the power cable
into the AC wall outlet.
■
Turning on this unit
Press
A
STANDBY/ON
(or
D
POWER
) to turn
on this unit.
y
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
■
Set this unit to the standby mode
Press
A
STANDBY/ON
(or
E
STANDBY
) to set
this unit to the standby mode.
In the standby mode, this unit consumes a small amount of power
in order to receive infrared signals from the remote control.
Connecting the FM and AM
antennas
Notes
DEO
ANTENNA
R
SURRO
AUDIO
OUTP
DVR
CD
S
N
OUT
DVR
AM
GND
FM
UNBAL.
75
N
OUT
MONITOR
OUT
MD/
CD-R
OUT
(REC)
IN
(PLAY)
AM loop
antenna
(supplied)
Ground
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
Indoor FM
antenna
(supplied)
Outdoor AM antenna
Use a 5 to 10 m (16 to 32
ft) of vinyl-covered wire
extended outdoors from a
window.
Open the
lever
Insert
Close the
lever
Note
Connecting the power cable
Turning on and off the power
Note
(U.S.A. model)
Power cable
To the AC wall outlet