Yamaha RX-V4600 MCXSP10 Manual - Page 113

The remote control, does not work or, function properly., does not learn new, functions.

Get Yamaha RX-V4600 - AV Receiver PDF manuals and user guides
UPC - 027108922683
View all Yamaha RX-V4600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

■ Remote control TROUBLESHOOTING Problem The remote control does not work or function properly. The remote control does not "learn" new functions. Cause Remedy Refer to page Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees off- 9 axis from the front panel. Direct sunlight or lighting (from an Reposition this unit. inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this - unit. The batteries are weak. Replace all batteries. 4 AMP/SOURCE/TV is set incorrectly. Set AMP/SOURCE/TV correctly. When operating this unit, set it to the AMP position. When operating the component selected by the input selector button, set it to the SOURCE position. - When operating the TV set in the DTV or PHONO area, set it to the TV position. The remote control code was not correctly Set the remote control code correctly using set. "LIST OF REMOTE CONTROL CODES" at the end 71 of this manual. Try setting another code of the same manufacturer using "LIST OF REMOTE CONTROL CODES" at 71 the end of this manual. This unit's library code and the remote control ID do not match. Switch the library code. 71 Even if the remote control code is Program the necessary functions independently into correctly set, there are some models that the programmable buttons using the Learn feature. 73 do not respond to the remote control. The batteries of this remote control and/or Replace the batteries. the other remote control are too weak. 4 The distance between the two remote controls is too much or too little. Place the remote controls at the proper distance. 73 The signal coding or modulation of the Learning is not possible. other remote control is not compatible - with this remote control. Memory capacity is full. Delete other unnecessary functions to make room for the new functions. 78 ADDITIONAL INFORMATION 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
109
TROUBLESHOOTING
ADDITIONAL
INFORMATION
■
Remote control
Problem
Cause
Remedy
Refer to
page
The remote control
does not work or
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
9
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
4
AMP/SOURCE/TV is set incorrectly.
Set AMP/SOURCE/TV correctly.
When operating this unit, set it to the AMP position.
When operating the component selected by the input
selector button, set it to the SOURCE position.
When operating the TV set in the DTV or PHONO
area, set it to the TV position.
—
The remote control code was not correctly
set.
Set the remote control code correctly using
“LIST OF REMOTE CONTROL CODES” at the end
of this manual.
71
Try setting another code of the same manufacturer
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
71
This unit’s library code and the remote
control ID do not match.
Switch the library code.
71
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Program the necessary functions independently into
the programmable buttons using the Learn feature.
73
The remote control
does not “learn” new
functions.
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
4
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper distance.
73
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
—
Memory capacity is full.
Delete other unnecessary functions to make room for
the new functions.
78