ZyXEL omni.net Plus User Guide - Page 40

Table 4-9 Supported Commands per TIA PN2388 8/20/90, Table 4-10 Class 2 Command Responses

Get ZyXEL omni.net Plus PDF manuals and user guides View all ZyXEL omni.net Plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Omni 56K Plus Series User's Guide Table 4-9 Supported Commands (per TIA PN2388 8/20/90) COMMAND DESCRIPTION VALUE Page bad; procedure interrupt requested. n=4 Page good; procedure interrupt requested. n=5 +FREL=n Phase C received EOL alignment: The EOL patterns are bit aligned as received. n=0 The last received bits of EOL patterns are byte aligned by the DCE, n=1 with necessary zero fill bits inserted. Refer to TIA PN-2388 for details. +FREV? Request the DCE revision identification. +FSPL=n "Enable polling" command: Disable polling. n=0 Enable polling. n=1 All other +F commands are not supported, but the modem will respond OK. In many cases this means "don't care". Table 4-10 Class 2 Command Responses RESPONSE +FCFR +FCIG:"string" +FCON +FCSI:"string" +FDCS:vr,br,wd,ln,df,ec,bf,st VALUE +FDIS:vr,br,wd,ln,df,ec,bf,st +FDTC:vr,br,wd,ln,df,ec,bf,st +FET:n +FHNG:n +FNSC:"HEX string" +FNSF:"HEX string" +FNSS:"HEX string" n=00 n=10 n=20 n=40 n=50 n=70 n=90 n=100 FUNCTION AND DESCRIPTION Confirmation . Report remote ID response CIG. Facsimile connection response. Report remote ID response CSI. Report session parameters response; refer to +FDCC=.... command. Report session negotiation parameters response; refer to +FDCC=.... command. Report remote capabilities response; refer to +FDCC=.... command. Post page message response; refer to the +FET=n command. Call termination status response. Normal and proper end of connection. Transmit error on phase A hang up code. Transmit error on phase B hang up code. Transmit error on phase C hang up code. Transmit error on phase D hang up code. Receive error on phase B hang up code. Receive error on phase C hang up code. Receive error on phase D hang up code. Report the non-standard facilities command frame. Report the non-standard facilities frame response. Report the non-standard setup frame response. 4-12 Command Sets

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Omni 56K Plus Series User’s Guide
4-12
Command Sets
Table 4-9 Supported Commands (per TIA PN2388 8/20/90)
COMMAND
DESCRIPTION
VALUE
Page bad; procedure interrupt requested.
n=4
Page good; procedure interrupt requested.
n=5
+FREL=n
Phase C received EOL alignment:
The EOL patterns are bit aligned as received.
n=0
The last received bits of EOL patterns are byte aligned by the DCE,
with necessary zero fill bits inserted. Refer to TIA PN-2388 for details.
n=1
+FREV?
Request the DCE revision identification.
+FSPL=n
"Enable polling" command:
Disable polling.
n=0
Enable polling.
n=1
All other +F commands are not supported, but the modem will respond OK. In many cases this means
"don't care".
Table 4-10 Class 2 Command Responses
RESPONSE
VALUE
FUNCTION AND DESCRIPTION
+FCFR
Confirmation .
+FCIG:"string"
Report remote ID response CIG.
+FCON
Facsimile connection response.
+FCSI:"string"
Report remote ID response CSI.
+FDCS:vr,br,wd,ln,df,ec,bf,st
Report session parameters response; refer to
+FDCC=
....
command.
+FDIS:vr,br,wd,ln,df,ec,bf,st
Report session negotiation parameters response; refer to
+FDCC=
....
command.
+FDTC:vr,br,wd,ln,df,ec,bf,st
Report remote capabilities response; refer to
+FDCC=
....
command.
+FET:n
Post page message response; refer to the +FET=n command.
Call termination status response.
n=00
Normal and proper end of connection.
n=10
Transmit error on phase A hang up code.
n=20
Transmit error on phase B hang up code.
n=40
Transmit error on phase C hang up code.
n=50
Transmit error on phase D hang up code.
n=70
Receive error on phase B hang up code.
n=90
Receive error on phase C hang up code.
+FHNG:n
n=100
Receive error on phase D hang up code.
+FNSC:"HEX string"
Report the non-standard facilities command frame.
+FNSF:"HEX string"
Report the non-standard facilities frame response.
+FNSS:"HEX string"
Report the non-standard setup frame response.