Acer Altos 1100e Acer Altos 1100e User's Guide - Page 150

Device connected, but not ready, Format Disk, Enabled

Get Acer Altos 1100e PDF manuals and user guides View all Acer Altos 1100e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

3. Perform a SCSI low-level format with the Format Disk utility under SCSI Disk Utilities in the SCSISelect utility. All data on the target drive will be lost when you run the Format Disk utility. Back up your data before you run it! 4. In the SCSISelect Advanced Configuration Options menu, set Extended BIOS Translation to Enabled. 5. Partition the drive again. 6. Restore data to the drive, if necessary. 4.5.1 Device connected, but not ready This message appears if the SCSI controller receives no answer when it requests data from an installed SCSI device. The SCSI controller skips this device and moves on to the next device on the bus. Do the following if you see this message when you request data from a SCSI drive: 1. Run the SCSISelect utility and access SCSI Device Configuration. Locate the host controller's SCSI ID and set Send Start Unit Command to yes. 2. Exit the SCSISelect utility and request data from the drive again. 3. If the message still appears, follow the drive manufacturer's instructions to make sure the drive is set to spin-up when the power is switched ON. Altos 1100E Series User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
Altos 1100E Series User’s Guide
3.
Perform a SCSI low-level format with the
Format Disk
utility under SCSI Disk
Utilities in the SCSI
Select
utility.
All data on the target drive will be lost when
you run the
Format Disk
utility. Back up your
data before you run it!
4.
In the SCSI
Select
Advanced Configuration Options menu, set Extended BIOS -
Translation to
Enabled
.
5.
Partition the drive again.
6.
Restore data to the drive, if necessary.
4.5.1
Device connected, but not ready
This message appears if the SCSI controller receives no answer when it requests
data from an installed SCSI device. The SCSI controller skips this device and
moves on to the next device on the bus.
Do the following if you see this message when you request data from a SCSI drive:
1.
Run the SCSI
Select
utility and access SCSI Device Configuration.
Locate the
host controller's SCSI ID and set Send Start Unit Command to
yes
.
2.
Exit the SCSI
Select
utility and request data from the drive again.
3.
If the message still appears, follow the drive manufacturer's instructions to
make sure the drive is set to spin-up when the power is switched ON.