Alcatel OS6400-48 Hardware User Guide - Page 77

Installing DC Power Source Wire Leads, Opening Connector for Ground Wire, Warning.

Get Alcatel OS6400-48 PDF manuals and user guides View all Alcatel OS6400-48 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Mounting OS6400 Switches Connecting Chassis to Power Source A clamp inside each slot keeps the power wire tightly in place during operation. The DC power supply has side screws that can be used to remove the connector if required. Installing DC Power Source Wire Leads These instructions describe how to connect your 3-wire DC power source to the power connector on your DC power supply. A small flat-tip screwdriver and a wire stripper are required for this procedure. 1 Prepare the three (3) wires-12 gauge-that will plug into the power supply. First make sure they are not plugged into the DC power source. Next, use a wire stripper to carefully strip between .24 and .29 inches (6-7.5mm) off the end of each wire, removing the outer insulation to expose the copper core. 2 Open the clamp for the ground wire slot by inserting a small flat-tip screwdriver into the top of the appropriate circular hole. Loosen the screw so that the clamp for the ground wire opens. Loosen Screw. + - Clamp inside square hole will open when screw is loosened in top circular hole. Opening Connector for Ground Wire 3 Insert the ground wire lead into the slot. The lead you insert must match the lead attached to the DC power source. Warning. You must plug DC wire leads into the correct holes in the DC power connector. Use the labels above the DC power connector as a guide to positive, negative, and ground connections. If the wire leads are plugged into the wrong holes, the power supply will not work properly and damage to the unit may result. Push the wire in far enough such that it reaches the back wall of the connector, about a half inch inside. + - Ground Wire Attaching the Ground Wire OmniSwitch 6400 Series Hardware Users Guide July 2010 page 3-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Mounting OS6400 Switches
Connecting Chassis to Power Source
OmniSwitch 6400 Series Hardware Users Guide
July 2010
page 3-21
A clamp inside each slot keeps the power wire tightly in place during operation.
The DC power supply has side screws that can be used to remove the connector if required.
Installing DC Power Source Wire Leads
These instructions describe how to connect your 3-wire DC power source to the power connector on your
DC power supply. A small flat-tip screwdriver and a wire stripper are required for this procedure.
1
Prepare the three (3) wires—12 gauge—that will plug into the power supply. First make sure they are
not plugged into the DC power source. Next, use a wire stripper to carefully strip between .24 and .29
inches (6-7.5mm) off the end of each wire, removing the outer insulation to expose the copper core.
2
Open the clamp for the ground wire slot by inserting a small flat-tip screwdriver into the top of the
appropriate circular hole. Loosen the screw so that the clamp for the ground wire opens.
Opening Connector for Ground Wire
3
Insert the ground wire lead into the slot. The lead you insert
must
match the lead attached to the DC
power source.
Warning.
You must plug DC wire leads into the correct holes in the DC power connector. Use the labels
above the DC power connector as a guide to positive, negative, and ground connections. If the wire leads
are plugged into the wrong holes, the power supply will not work properly and damage to the unit may
result.
Push the wire in far enough such that it reaches the back wall of the connector, about a half inch
inside.
Attaching the Ground Wire
Clamp inside square hole will open
when screw is loosened in top cir-
cular hole.
Loosen Screw
.
+ -
Ground Wire
+ -