Alcatel OS6602-24 Getting Started Guide - Page 19

Rack Mounting Stacked Configurations

Get Alcatel OS6602-24 PDF manuals and user guides View all Alcatel OS6602-24 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

9 Plug the power cord (supplied) into the power socket located on the switch's rear panel; next, plug the cord into an easily-accessible grounded AC power source. See "Electrical Requirements" on page 6 for more information. Note. Do not turn on the power supply at this time. You will power on the switch later in the setup process. 10 If you wish to install a supplemental ground for the switch, you may attach a type LCD8-10A-L grounding lug to the grounding lug, located on the switch's rear panel. Install the type LCD8-10A-L grounding lug per manufacturer's specifications. 11 If you are installing multiple switches in a rack to form a stacked configuration, refer to "Rack Mounting Stacked Configurations" on page 13. If you are not installing a stacked configuration, continue to "Installing a Back Up Power Supply (OS6624, OS6648, OS6600-U24)" on page 14. Rack Mounting Stacked Configurations If you are rack mounting multiple switches in a stacked configuration, be sure to place all switches in verticallyadjacent rack positions. This will ensure that all required stacking cables will have adequate length for the installation. For additional instructions on rack mounting a stacked configuration, follow the steps below: 1 Install the rack mount flanges for all switches that are to be included in the stacked configuration, as described on page 11. Up to eight switches may be stacked to form a single virtual chassis. 2 Place the next switch in the stack directly on top of the previously installed switch. 3 Align the holes in the flanges with the holes in the rack's vertical posts. 4 Once the holes are aligned, insert a rack mount screw through the bottom hole of each flange. Tighten both screws until they are secure. Once the screws at the bottom of each flange are secure, install the remaining two rack mount screws. Be sure that all screws are securely tightened. 5 Repeat steps 1 through 4 above for all remaining switches. 6 On OS6624, OS6648, OS660-U24, and OS6600-P24 switches verify that the on/off switch for each OmniSwitch 6600 Family switch is in the off ( O ) position. March 2005 Setting Up the Hardware 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
March 2005
Setting Up the Hardware
13
9
Plug the power cord (supplied) into the power socket
located on the switch’s rear panel; next, plug the cord into
an easily-accessible grounded AC power source. See
“Electrical Requirements” on page 6
for more informa-
tion.
Note.
Do not
turn on the power supply at this time. You
will power on the switch later in the setup process.
10
If you wish to install a supplemental ground for the
switch, you may attach a type LCD8-10A-L grounding lug
to the grounding lug, located on the switch’s rear panel.
Install the type LCD8-10A-L grounding lug per manufac-
turer’s specifications.
11
If you are installing multiple switches in a rack to
form a stacked configuration, refer to
“Rack Mounting
Stacked Configurations” on page 13
. If you are not install-
ing a stacked configuration, continue to
“Installing a Back
Up Power Supply (OS6624, OS6648, OS6600-U24)” on
page 14
.
Rack Mounting Stacked Configurations
If you are rack mounting multiple switches in a stacked
configuration, be sure to place all switches in vertically-
adjacent rack positions. This will ensure that all required
stacking cables will have adequate length for the installation.
For additional instructions on rack mounting a stacked config-
uration, follow the steps below:
1
Install the rack mount flanges for
all switches
that are
to be included in the stacked configuration, as described
on
page 11
. Up to eight switches may be stacked to form a
single virtual chassis.
2
Place the next switch in the stack directly on top of the
previously installed switch.
3
Align the holes in the flanges with the holes in the
rack’s vertical posts.
4
Once the holes are aligned, insert a rack mount screw
through the bottom hole of each flange. Tighten both
screws until they are secure. Once the screws at the
bottom of each flange are secure, install the remaining two
rack mount screws. Be sure that all screws are securely
tightened.
5
Repeat steps 1 through 4 above for all remaining
switches.
6
On OS6624, OS6648, OS660-U24, and OS6600-P24
switches verify that the on/off switch for each
OmniSwitch 6600 Family switch is in the off ( O ) posi-
tion.