Alpine CDE-HD137BT Owners Manual (english) - Page 16

Sound Setting Rotary encoder/ /ENTER 2 Turn the Rotary encoder until the desired sound is obtained in each mode. By setting DEFEAT ON, previously adjusted settings of BASS, MID, TRE LEVEL and LOUDNESS will return to the factory defaults. Audio Setup AUDIO/SETUP Adjusting Subwoofer Level/Bass Level/ Middle Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Loudness/Defeat 1 Press AUDIOSETUP repeatedly to choose the desired mode. Each press changes the mode as follows: SUBWOOFER*1  BASS LEVEL*2  MID LEVEL*2/*4  TRE LEVEL*2  BALANCE  FADER  LOUDNESS*2/*3/*4  DEFEAT  VOLUME  SUBWOOFER *1 When the subwoofer mode is set to OFF, its level cannot be adjusted. *2 Adjustable only when DEFEAT is OFF. *3 For details about loudness, refer to "Turning Loudness On/Off (CDE-HD137BT Only)" on page 17. *4 Only for CDE-HD137BT. Subwoofer Bass level Middle level Treble level Balance Fader Loudness Defeat Volume +0 ~ +15 −7 ~ +7*4 / −6 ~ +6*5 −7 ~ +7*4 −7 ~ +7*4 / −6 ~ +6*6 L15 ~ R15 R15 ~ F15 ON/OFF ON/OFF 0 ~ 35 *5 Only for CDE-HD138BT. Setting value will change according to the level value set in BAND1 of P-EQ or G-EQ. Refer to "Adjusting the Parametric Equalizer Curve (5BAND P.EQ) (CDE-HD138BT Only)" on page 17 or refer to "Adjusting the Graphic Equalizer Curve (7BAND G.EQ) (CDE-HD138BT Only)" on page 17. *6 Only for CDE-HD138BT. Setting value will change according to the level value set in BAND5 of P-EQ or BAND7 of G-EQ. Refer to "Adjusting the Parametric Equalizer Curve (5BAND P.EQ) (CDE-HD138BT Only)" on page 17 or refer to "Adjusting the Graphic Equalizer Curve (7BAND G.EQ) (CDE-HD138BT Only)" on page 17. Note • If no operation is performed for 5 seconds, the unit automatically returns to normal mode. You can flexibly customize the unit to suit your own preference and usage. From the AUDIO SETUP menu, Audio Setting can be modified. Use steps 1 to 5 to select the category you wish to modify. For details on how to change each setting, see the following sections below. 1 Press and hold AUDIOSETUP for at least 2 seconds to activate the SETUP mode. 2 Turn the Rotary encoder to select AUDIO, and then press ENTER. AUDIO  GENERAL  DISPLAY  TUNER  SIRIUSXM*6  iPod  BLUETOOTH 3 Turn the Rotary encoder to select the desired sound setting menu, and then press ENTER. (e.g. Select SUBWOOFER) FACTORY EQ*1/*2  LOUDNESS*1/*2  EQ MODE*2/*6  5BAND P.EQ*2/*3  7BAND G.EQ*2/*4  MX SETTING*2  3BAND EQ*1  VOL LV ADJ  HPF*2  SUBWOOFER  SUBW LPF*5  SUBW PHASE*5  SUBW SYS*5  POWER IC *1 Only for CDE-HD137BT. *2 Adjustment cannot be performed when DEFEAT is set to ON. *3 Only for CDE-HD138BT. Displayed when EQ MODE is set to 5BAND P.EQ. *4 Only for CDE-HD138BT. Displayed when EQ MODE is set to 7BAND G.EQ. *5 These functions are inoperable when Subwoofer is set to OFF. *6 Only for CDE-HD138BT. 4 Turn the Rotary encoder to change the setting, and then press ENTER. (e.g. Select SUBW ON or SUBW OFF) 5 Press and hold AUDIOSETUP for at least 2 seconds to return to normal mode. Notes • Pressing  returns to the previous Sound menu mode. • Pressing and holding  for at least 2 seconds will return to normal mode. • If no operation is performed for 60 seconds, Sound menu mode is canceled. 16-EN