Asus KN97 User Manual - Page 42

ASUS KN97-X User's Manual, Auto detection of hard disks on bootup, Drive A / Drive B None, Floppy 3

Get Asus KN97 PDF manuals and user guides View all Asus KN97 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

IV. BIOS SOFTWARE Auto detection of hard disks on bootup For each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE drives during bootup. This will allow you to change your hard drives (with the power off) and then power on without having to reconfigure your hard drive type. If you use older hard drives which do not support this feature, then you must configure the hard drive in the standard method as described above by the "User" option. NOTE: After the IDE hard disk drive information has been entered into BIOS, new IDE hard disk drives must be partitioned (such as with FDISK) and then formatted before data can be read from and write on. Primary IDE hard disk drives must have its partition set to active (also possible with FDISK). NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Drive A / Drive B (None) These fields record the types of floppy disk drives installed in your system. The available options for drives A and B are: 360KB, 5.25 in.; 1.2MB, 5.25 in.; 720KB, 3.5 in.; 1.44MB, 3.5 in.; 2.88MB, 3.5 in.; None To enter the configuration value for a particular drive, highlight its corresponding field and then select the drive type using the left- or right-arrow key. Floppy 3 Mode Support (Disabled) This is the Japanese standard floppy drive. The standard stores 1.2MB in a 3.5inch diskette. This is normally disabled but you may choose from either: Drive A, Drive B, Both, and Disabled Video (EGA/VGA) Set this field to the type of video display card installed in your system. The options are: EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA 80 If you are using a VGA or any higher resolution card, choose the "EGA/VGA" option. Halt On (All Errors) This field determines which types of errors will cause the system to halt. Choose from All Errors, No Errors, All, But Keyboard, All, But Diskette, and All, But Disk/Key. IV. BIOS (Standard CMOS) 42 ASUS KN97-X User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS KN97-X User’s Manual
42
IV.
BIOS SOFTWARE
IV.
BIOS
(Standard CMOS)
Auto detection of hard disks on bootup
For each field:
Primary Master, Primary Slave, Secondary Master, and Secondary
Slave, you can select
Auto
under the TYPE and MODE fields.
This will enable auto
detection of your IDE drives during bootup.
This will allow you to change your
hard drives (with the power off) and then power on without having to reconfigure
your hard drive type.
If you use older hard drives which do not support this feature,
then you must configure the hard drive in the standard method as described above
by the “User” option.
NOTE:
After the IDE hard disk drive information has been entered into BIOS, new
IDE hard disk drives must be partitioned (such as with FDISK) and then formatted
before data can be read from and write on.
Primary IDE hard disk drives must have
its partition set to
active
(also possible with FDISK).
NOTE:
SETUP Defaults are noted in parenthesis next to each function heading.
Drive A / Drive B (None)
These fields record the types of floppy disk drives installed in your system.
The
available options for drives A and B are:
360KB, 5.25 in.; 1.2MB, 5.25 in.; 720KB,
3.5 in.; 1.44MB, 3.5 in.; 2.88MB, 3.5 in.; None
To enter the configuration value for a particular drive, highlight its corresponding
field and then select the drive type using the left- or right-arrow key.
Floppy 3 Mode Support (Disabled)
This is the Japanese standard floppy drive.
The standard stores 1.2MB in a 3.5inch
diskette.
This is normally disabled but you may choose from either:
Drive A, Drive
B, Both, and Disabled
Video (EGA/VGA)
Set this field to the type of video display card installed in your system.
The options
are:
EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA 80
If you are using a VGA or any higher resolution card, choose the “EGA/VGA”
option.
Halt On (All Errors)
This field determines which types of errors will cause the system to halt.
Choose from
All Errors, No Errors, All, But Keyboard, All, But Diskette, and All, But Disk/Key.