Asus KN97 User Manual - Page 44

Enabled, Disabled, A,CDROM,C, CDROM,C,A, Read Only, HDD MAX, Disabled 2, 4, 8, 16, System, Setup,

Get Asus KN97 PDF manuals and user guides View all Asus KN97 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

IV. BIOS SOFTWARE CPU Fast String (Enabled) Leave on default setting of Enabled for best performance. Deturbo Mode (Disabled) When Enabled, FLUSH# signal is held asserted to disable caching and the P6 bus pipeline will be stalled. This allows software to run at a reduced-speed. The default is set to Disabled to allow maximum processing speed. Quick Power On Self Test (Enabled) This field speeds up the Power-On Self Test (POST) routine by skipping retesting a second, third, and forth time. Setup default setting for this field is Enabled. A complete test of the system is done on each test. HDD Sequence SCSI/IDE First (IDE) When using both SCSI and IDE hard disk drives, IDE is always the boot disk using drive letter C (default setting of IDE). This new feature allows a SCSI hard disk drive to be the boot disk when set to SCSI. This allows multiple operating systems to be used on both IDE and SCSI drives or the primary operating system to boot using a SCSI hard disk drive. Boot Sequence (C,A) This field determines where the system looks first for an operating system. Options are A,CDROM,C; CDROM,C,A; A,C; C,A The setup default setting is to check first the hard disk and then the floppy drive; that is, C, A. Boot Up Floppy Seek (Disabled) When enabled, the BIOS will seek the floppy "A" drive one time. Floppy Disk Access Control (R/W) This allows protection of files from the computer system to be copied to floppy drives by allowing the setting of Read Only to only allow reads from the floppy but not writes. The setup default R/W allows both reads and writes. IDE HDD Block Mode Sectors (HDD MAX) This field enhances hard disk performance by making multi-sector transfers instead of one sector per transfer. Most IDE drives, except older versions, can utilize this feature. Selections are HDD MAX, Disabled 2, 4, 8, 16, and 32. Security Option (System) This field determines when the system prompts for the password. The default setting is System, where the system prompts for the User Password every time you boot up. The other option is Setup, where the system always boots up, and prompts for the Supervisor Password only when the Setup utility is called up. You can specify a password by using the Supervisor Password or User Password option from the main screen as explained later in this section. IV. BIOS (BIOS Features) 44 ASUS KN97-X User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS KN97-X User’s Manual
44
IV.
BIOS SOFTWARE
IV.
BIOS
(BIOS Features)
CPU Fast String (Enabled)
Leave on default setting of
Enabled
for best performance.
Deturbo Mode (Disabled)
When
Enabled
, FLUSH# signal is held asserted to disable caching and the P6 bus
pipeline will be stalled.
This allows software to run at a reduced-speed.
The default
is set to
Disabled
to allow maximum processing speed.
Quick Power On Self Test (Enabled)
This field speeds up the Power-On Self Test (POST) routine by skipping retesting a
second, third, and forth time.
Setup default setting for this field is
Enabled
.
A
complete test of the system is done on each test.
HDD Sequence SCSI/IDE First (IDE)
When using both SCSI and IDE hard disk drives, IDE is always the boot disk using
drive letter C (default setting of
IDE
).
This new feature allows a SCSI hard disk
drive to be the boot disk when set to
SCSI
.
This allows multiple operating systems
to be used on both IDE and SCSI drives or the primary operating system to boot
using a SCSI hard disk drive.
Boot Sequence (C,A)
This field determines where the system looks first for an operating system.
Options
are
A,CDROM,C
;
CDROM,C,A
;
A,C
;
C,A
The setup default setting is to check first
the hard disk and then the floppy drive; that is,
C, A
.
Boot Up Floppy Seek (Disabled)
When enabled, the BIOS will seek the floppy “A” drive one time.
Floppy Disk Access Control (R/W)
This allows protection of files from the computer system to be copied to floppy
drives by allowing the setting of
Read Only
to only allow reads from the floppy but
not writes.
The setup default
R/W
allows both reads and writes.
IDE HDD Block Mode Sectors (HDD MAX)
This field enhances hard disk performance by making multi-sector transfers instead
of one sector per transfer.
Most IDE drives, except older versions, can utilize this
feature.
Selections are
HDD MAX, Disabled 2, 4, 8, 16,
and
32
.
Security Option (System)
This field determines when the system prompts for the password.
The default set-
ting is
System
, where the system prompts for the User Password every time you boot
up.
The other option is
Setup
, where the system always boots up, and prompts for
the Supervisor Password only when the Setup utility is called up.
You can specify a
password by using the
Supervisor Password
or
User Password
option from the main
screen as explained later in this section.