Bernina Bernette 340 deco User Guide - Page 10

Winding the bobbin, Notes - machine

Get Bernina Bernette 340 deco PDF manuals and user guides View all Bernina Bernette 340 deco manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Getting ready to Embroider 9 1 1 2 Winding the bobbin Guide the thread around the bobbin winder thread guide while holding the thread at the spool. 1. Bobbin winder thread guide Thread through the hole in the bobbin from the inside to the outside. Put the bobbin on the bobbin winder spindle. 2 Bobbin winder spindle Push the spindle to the right. Press the Start/Stop button while holding the end of the thread. Stop the machine after the bobbin has made a few turns. Cut the thread close to the hole in the bobbin. Press the Start/Stop button again. When the bobbin is fully wound it will stop automatically. Press the Start/Stop button to stop the machine then return the bobbin winder spindle to the left. Remove the bobbin and cut the thread with the bobbin thread cutter. 3 3. Bobbin thread cutter Notes: Do not move the bobbin winder spindle while the machine is running. For safety purposes, the motor will stop automatically after running for two minutes. Adjust how much the bobbin is filled by rotating the bobbin winder stopper. To achieve the best embroidery quality, BERNINA recommends to use only high quality bobbin thread such as OESD 41ET/W or Mettler®

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Getting ready to Embroider
9
Winding the bobbin
Guide the thread around the bobbin winder thread guide while
holding the thread at the spool.
1.
Bobbin winder thread guide
Thread through the hole in the bobbin from the inside to the
outside. Put the bobbin on the bobbin winder spindle.
2
Bobbin winder spindle
Push the spindle to the right. Press the Start/Stop button while
holding the end of the thread. Stop the machine after the bobbin
has made a few turns. Cut the thread close to the hole in the
bobbin. Press the Start/Stop button again. When the bobbin is fully
wound it will stop automatically. Press the Start/Stop button to stop
the machine then return the bobbin winder spindle to the left.
Remove the bobbin and cut the thread with the bobbin thread
cutter.
3.
Bobbin thread cutter
Notes:
Do not move the bobbin winder spindle while the machine is
running. For safety purposes, the motor will stop automatically after
running for two minutes.
Adjust how much the bobbin is filled by rotating the bobbin winder
stopper.
To achieve the best embroidery quality, BERNINA recommends to use
only high quality bobbin thread such as OESD 41ET/W or Mettler
®
1
1
2
3