Bosch NWD-495V03-20P Operating Instructions - Page 24

Mount the camera

Get Bosch NWD-495V03-20P PDF manuals and user guides View all Bosch NWD-495V03-20P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

24 en | Mounting the unit FlexiDomeDN IP 3.2.1 3.2.2 Power connection 1. Use a class 2 power supply 24 VAC or +12 VDC. 2. Use AWG16 to 22 stranded wire or AWG16 to 26 solid wire; cut back 10 mm (0.4 inch) of insulation. 3. Run the power wires through the closed rubber grommet of the connection box cover. 4. Attach the power wires to the supplied plug (polarity is not important) as follows: Pin Wire 1 + 2 Ground 3 - Power connector 12 3 5. Connect the power plug to the connector in the connection box. Network (and PoE) connection 1. Use a shielded UTP Category 5 cable. NOTICE! Power can be supplied to the camera via the Ethernet cable, compliant with the Power-over-Ethernet (IEEE 802.3af) standard. 2. Crimp a RJ45 connector onto the cable. 3. Connect the network cable to the network connector in the connection box. 3.3 Mount the camera 1. Close and screw on the cover of the connection box to secure it. 2. Slide the connection box back into its position in the base. 3. Push the connections back through the surface wire hole. 4. Secure the integrated camera and base to the mounting plate with three screws. V 1.0 | 2006.12 Operating Instructions Bosch Security Systems

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
24
en | Mounting the unit
FlexiDome
DN
IP
V 1.0 | 2006.12
Operating Instructions
Bosch Security Systems
3.2.1
Power connection
1.
Use a class 2 power supply 24 VAC or +12 VDC.
2.
Use AWG16 to 22 stranded wire or AWG16 to 26 solid
wire; cut back 10 mm (0.4 inch) of insulation.
3.
Run the power wires through the closed rubber grommet
of the connection box cover.
4.
Attach the power wires to the supplied plug (polarity is not
important) as follows:
5.
Connect the power plug to the connector in the connec-
tion box.
3.2.2
Network (and PoE) connection
1.
Use a shielded UTP Category 5 cable.
NOTICE!
Power can be supplied to the camera via the Ethernet
cable, compliant with the Power-over-Ethernet (IEEE 802.3af)
standard.
2.
Crimp a RJ45 connector onto the cable.
3.
Connect the network cable to the network connector in
the connection box.
3.3
Mount the camera
1.
Close and screw on the cover of the connection box to
secure it.
2.
Slide the connection box back into its position in the base.
3.
Push the connections back through the surface wire hole.
4.
Secure the integrated camera and base to the mounting
plate with three screws.
1
3
2
Pin
Wire
1
+
2
Ground
3
–
Power connector